Top 20 Bosch HBL 755 Stainless Steel Electric Double Oven Questions & Answers

I found a users manual for Bosch wall ovens at Retrevo.com

http://www.retrevo.com/s/Bosch-HBL755AUC-Ovens-review-manual/id/925ci470/t/1-2/

Same on ours... one seems like it is just softly lying against the gasket without a solid tight seal... doesn't bother the cooking much, it seems, but I hate little problems like this!

Will follow this thread to see if there is an adjustment for a DIY'er, without having to make a $120 service call...

Hi, well the only thing that can cause this is a shorted controller switch, or a faulty controller, sometimes it can be the thermostat, jammed on,or even a jammed relay, or relay driver.
However to have even a remote chance of a DIY repair one simply MUST obtain a service manual, this shows you how to troubleshoot and isolate a problem for repair. As many Symptoms may have widely differing Causes.
As a professional, I always advice that one should seek a professional, usually it ends up actually being fixed, and cheaper in the long run. Plus there is NO chance of electrocution.

below is your Bosch service link, you can get a manual from here or arrange for a service call.
http://www.bosch-home.com/us/bosch/customer-care.html

We have here below the parts layout of your oven. The element you need to check if it is bad is the bake element which is located under cavity at the bottom of your oven.

http://www.appliancepartspros.com/partsearch/model.aspx?model_id=5110019&diagram_id=191359#d191359

We have the cooling fans in stock for the upper and lower ovens. Enter your model # at www.appliancehelponline.com. Select your part diagrams will also come up. All parts come with installation instructions.

there is a microswitch on the door inner it sounds like its come loose or broken away affecting its operating tolerances should be easy to replace.

i am in the uk and i use barkeepers friend this usually shifts anything on steel i dont know if you use something different in the u/s.its a white powdery substance which you aply with a damp clth then wipe of as it dries works superbly.

i am not aware of a bosch oven that locks the top door usually only main oven will lock if self clean pyro oven,the small oven never has this feature sounds more like a hinge problem check nothing is fouling the lower part of the oven door.

Yes your owners manual will show how.Replace the bulb with a similar bulb{ heat resistive}

HI. This will occur if the door lock mechanism is malfunctioning. This could be because of a failed connection, due to welded contacts, or a separated wring harness at the mechanism, or control board. Check these areas for faults. replace the door lock mechanism if all areas stated are ok, and connected well.

drop the door down as low as it will go look carefully at the hinges as they pass through into the oven chassis you will see a clip on each one that you lift up to lock the hinge you usually lift them up as far as they will go then this will lock the hinges as you close the door the hinges will come away from the oven complete with door.... reverse to refit.

Hi Jim. Thanks for your request re prob with your oven.
Unfortunately, this is not a problem I have come across before, so in this instance, I am unable to help solve it for you.
Only thing I can suggest at this time is that you check all connections and plug in connectors, you never know it could be caused by a bad or intermittent connection.
Once again, sorry I can't be of more help.

Hi! The location of the thermal fuse in a Bosch single wall oven may vary depending on the model, but it is typically located on the back of the oven. To locate the thermal fuse, follow these steps:

1. Turn off power to the oven: Before attempting any repairs, turn off the power to the oven by unplugging it or turning off the circuit breaker that supplies power to the oven.
2. Remove the back panel: Locate the screws or bolts that hold the back panel of the oven in place and remove them using a screwdriver or socket wrench. Carefully remove the back panel to access the components inside the oven.
3. Locate the thermal fuse: Look for a small, rectangular device with two wires attached to it. This is the thermal fuse. It may be located near the top or bottom of the back of the oven, depending on the model.
4. Check the thermal fuse for continuity: Use a multimeter to check the continuity of the thermal fuse. Set the multimeter to the ohms setting and touch the probes to the two terminals of the thermal fuse. If the multimeter shows no continuity, the thermal fuse has blown and needs to be replaced.
5. Replace the thermal fuse: If the thermal fuse has blown, replace it with a new one of the same rating. Install the new fuse in the same location as the old one and reattach the back panel of the oven.
6. Test the oven: After replacing the thermal fuse and reassembling the oven, turn on power to the oven and test it to ensure that it is working properly.

If you are not comfortable working with electrical components or if you are unable to locate the thermal fuse in your Bosch single wall oven, it's recommended to seek the assistance of a qualified technician. Kind regards

first thing I would do is check the cables that go to the clock, if they are OK then you likely have a faulty clock module which will need to be replaced.

Get some epoxy putty, grease the shaft with Vaseline, put a small pea size piece of epoxy rolled thinly and insert it into the knob where the flat part registers on the knob. Push the knob into place and leave it 24 hours to cure. I use this.

Epoxy Putty - Amazon.ca

https://www.amazon.ca > Epoxy-Putty > k=Epoxy+Putty Results 1 - 48 of 696 - Epoxy Putty Stick, Yanyi Moldable Epoxy Glue for Crack Damage Fixing Filling or Sealing. Fast Permanent Repair for Metal, Glass, Wood, ... ..

Yes, the tube is fed in from behind or above. Some thermostat bodies have a small adjusting screw to allow you to calibrate if it is fairly close. The videos show it is a simple job.

You may need to replace the thermocouple inside of the oven.

The issue you're experiencing with your Bosch convection microwave not heating in convection mode could be caused by a few different things. Here are a few things to check:

1. Check the settings: Make sure that the microwave is set to convection mode and that the temperature and time settings are correct.
2. Check the element: The bottom heating element is responsible for providing heat during convection mode. Make sure that the element is not damaged or burnt out. You can visually inspect it, if it is damaged it will need to be replaced.
3. Check the fan: The fan is responsible for circulating hot air during convection mode. Make sure that the fan is not blocked or damaged. If it is, it will need to be replaced.
4. Check the control board: The control board is responsible for controlling the functions of the microwave. A malfunctioning control board could prevent the microwave from heating in convection mode.
5. Check for a blown thermal fuse: A thermal fuse is a safety device that cuts off power to the oven if it overheats. If the thermal fuse is blown, it will need to be replaced.
6. Check for a blown thermal cut-off: A thermal cut-off is a device that cuts off power to the oven if it overheats. If the thermal cut-off is blown, it will need to be replaced.

The heating element is located on the back of the Bosch WAE24166GB/06 washing machine.

Generally it tells you that the food is cooked if the 'integrated oven has a microwave function. Or of course it is a fault. You can often fix that with a Power Reset. https://www.google.com/search?q=integrated+Bosch+oven+and+it+bleeps+when+I+open+the+oven+door+and+when+it+has+been+on+for+over+30+mins ..