20 Most Recent Ryobi Two 18V Lithium-Ion Batteries + Lithium-Ion Charger Upgrade Combo Pack - Page 10 Questions & Answers

No, Ryobi Corded Hammer Drills do not have fuses. To verify enter your model number on the Model Tab at the below listed Link and chose Wiring Diagram from the Pop-up which comes up after clicking on the found model(s) https://www.ryobitools.com/outdoor/support/parts Then Click on the GO TO POWER TOOLS PARTS STORE Button

Ryobi Drills | Answered on Jan 22, 2018

Australia has a 230v supply, and the US 110v. The power supply for your charger will indicate what input voltage it can handle. PCs, for example, typically have power supplies that can use anything between 100v and 240v, which means you can take your laptop from country to country without worrying. My Ryobi charger on the other hand says 240v input, so it doesn't have this flexibility - usually it wouldn't need to. If yours says 110v then you'll need a converter for it to function properly in Australia.

Ryobi Drills | Answered on Jan 21, 2018

Bad connection in the switch possibly, if it can be opened it may be touched up with steel wool,nail file or very light sand paper. If nothing else possibly a loose connection where the battery attaches to the wiring

Ryobi Drills | Answered on Jan 10, 2018

Ryobi P115 is an 18V battery charger. However, Ryobi Manual did not mention the current rating of P115. if the current rating of Ryobi P115 is 50% higher than your 18V Lithium Battery it will charge. but if it's less than or equal, it will not.

Ryobi Drills | Answered on Dec 02, 2017

Check the battery with your multimeter. If it reads below 36 volts (or whatever the cutoff point is) it may be damaged. But before you run off and buy a new one, use the multimeter to check the voltage from the charger.

Or borrow a good battery and see how your charger behaves.

that way, you can identify the cause of the problem

Ryobi Drills | Answered on Nov 27, 2017

test the battery with DMM-Digital Multi-Tester. when full charge a 36V battery measures 37-38 Volts. if battery is full charge the problem is your electric drill bring it to service center maybe need to replace carbon brush or the motor.

Ryobi Drills | Answered on Nov 26, 2017

I believe it is a P105 18V lithium battery.

Ryobi Drills | Answered on Oct 18, 2017

You have a weak cell in the battery therefore it isn't producing enough amps. Needs to be replaced.

Ryobi Drills | Answered on Sep 29, 2017

Battery or charger defective

Ryobi Drills | Answered on Sep 26, 2017

The battery has failed. Whether the battery can be reconditioned is not the question. The battery charger is condemning the battery when it does this. There are some battery fixes on you tube where a second battery can be used to get the dead battery off the zero voltage or low voltage limit that the charger is seeing. My response that the battery has failed is based on the charger symptoms and not on whether the battery can be reconditioned.

Ryobi Drills | Answered on Sep 09, 2017

I suspect the little ball bearings are out, possibly fell through the holes. Age and use and abrasive dust will cause this. You will need parts to replace the bit holder completely.

Ryobi Drills | Answered on Sep 09, 2017

all batteries wear out only need to change out battery unless charger is malfunctioning

Ryobi Drills | Answered on Aug 19, 2017

Not finding what you are looking for?
Ryobi Two  18V Lithium-Ion Batteries + Lithium-Ion Charger Upgrade Combo Pack Logo

114 questions posted

Ask a Question

Usually answered in minutes!

Top Ryobi Drills Experts


Level 3 Expert

2601 Answers

Cindy Wells

Level 3 Expert

6164 Answers


Level 3 Expert

85239 Answers

Are you a Ryobi Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ryobi Drills

  • Ryobi Drills

Most Popular Question

battery charger just not work anymore

  • Drills