20 Most Recent Makita 2704 Contractors 15 Amp 10 Inch Benchtop Table Saw - Page 6 Questions & Answers

0helpful
1answer

Makita 5007mg blade spins wont cut thought

blade bone or sitting upside down on the machine or the drive shaft is worn
2/6/2016 7:31:03 PM • Makita Saws • Answered on Feb 06, 2016
0helpful
1answer

Spark plug gap for makita dpc 7311

take the cover of a pack of cigarette paper then its most of the times right.
2/6/2016 10:58:10 AM • Makita Saws • Answered on Feb 06, 2016
0helpful
1answer

My grinder makita 9017,what was procedure before changing aremature? My aremature new ,what is further check up on capacitors?

For every machine if it is not working begin measure on the power cable if its not defect measure the carbon brushes to each other over the commutator of the armature (maybe only the auto-stop inside the brushes is activated ) when the brushes become to short there comes a little spring from inside the brush out to protect. measure the 2 or 4 electric field contacts to measure the 2 coils if that's good then measure the switch the capacitors ? no that is only on some machines called feedthrough capacitors like the brand FLEX has on its grinders , but Makita have i not seen in 20 years the capacitors in machines with brushes ( not induction motors) for only radio interference suppression you can without problems remove them it has nothing to do in function. switch and electronic can be defect this model 9017 is not common in my country but every machine has the same principle.
2/6/2016 10:52:28 AM • Makita Saws • Answered on Feb 06, 2016
0helpful
1answer

I have a makita BSS 610 cordless saw that has stopped working I've taken it apart and the armature winding all looks fine I've changed the brushes and it still won't work! Please help??

VERY IMPORTANT to tell you MAKITA HAS MODIFICATED the switch assembly and battery connector !!!!! of this device . If you have a saw with the 2 contacts in the connectorplate then the problem of an to early defect battery is possible by missing of a thirt protect connector to protect a to deep discharged battery . The new switch assembly has 3 contacts a - and a + and the very important Low Voltage Disconnect contact that should shut off in one time the machine it looks like its defect but its not !! thats the protection and then only take the battery in the charger . Because there must be a little dc in the battery left for the charger accept, if the battery is to low the charger will not accept the battery anymore then you will have to take the battery to someone with a special cadex charger to boost the dc again in or go to a special makita service , hold as much as possible the batteries on the charger to last the battery life. the best is if you have no protected 3 contacts connector to build it over Makita has moost of the time a little ridge on one side of the battery connector (marketing technical) because of the modification on the new connectorplate so it wont fit in the old housing hihihiiii but i I just cut it off with pliers and file it smooth, its easy so I can just use the old machine housing again you need for modification IF YOU NEED ?? or you have the new 3 contacts machine already and don,t know before of the stop function by lowered battery. but otherwise you need a new switch and connector both.
2/5/2016 9:58:26 AM • Makita Saws • Answered on Feb 05, 2016
0helpful
1answer

1221 chop saw. Why does brake function work some of the time but not all the time?

I've also been wondering me, I think the ankercommutator (collectors) where the brush is not flat enough, which is probably ingrained that cave. I set the anchor with a bearing on a lathe and the axis of the anchor in a drill and a fresh file (lack of a lathe) and I had some improvement.
2/5/2016 8:34:07 AM • Makita Saws • Answered on Feb 05, 2016
0helpful
1answer

What would cause a table saw to just stop working?

Sound like the motor finally went to motor heaven. If you have an ohm meter do a continuity test of the motor. Should be a low ohm reading. If high or infinity, fogit it. One last thought! - check the motor brushes !!!!!!!!!!!!! If no contact with commutator the motor will not not be energized.
1/2/2016 3:23:55 AM • Makita Saws • Answered on Jan 02, 2016
0helpful
1answer

My Makita 6400 petrol saw stopped running , when I pressed decompretion button and tried to start loads of petrol came out of it, help!

Where did the petrol come out from? The tank lid or the muffler or somewhere else?
5/11/2015 1:53:20 AM • Makita Saws • Answered on May 11, 2015
0helpful
1answer

Not cutting accurate in the A position sawing to the right of my pencil line

so,remember that and move the wood to the left or find someone that knows how to operate a saw
4/29/2015 9:03:36 PM • Makita Saws • Answered on Apr 29, 2015
0helpful
1answer

Saw not cutting accurate in A position cutting to the right of the pencil line

you are cutting to the right,the mark on the saw is only a reference,it is up to you to figure where to saw
4/29/2015 9:00:57 PM • Makita Saws • Answered on Apr 29, 2015
0helpful
1answer

How do I lift the saw mechanism on a Makita LS1040. It is locked and cannot trace any release mechanism. Danie

It's on the righthand side of the saw at the hinge area in the back. If that is unlocked then it could be the guard linkage hanging up.
2/19/2015 6:08:21 AM • Makita Saws • Answered on Feb 19, 2015
0helpful
1answer

My makita 4.5"angle grinder produces alot of sparks at the brushes.what could be wrong?

lots of sparks means your brushes are used up, broken or stuck. Replace them. If that is not the problem, it could be you over heated the motor, very difficult to do, and the motor is about to die. Check brushes first. You can tell by examining your graphite brushes. Use a straight screw driver and unscrew the black cap that holds the brushes in place.
2/17/2015 7:30:13 PM • Makita Saws • Answered on Feb 17, 2015
Not finding what you are looking for?
Makita 2704 Contractors 15 Amp 10 Inch Benchtop Table Saw Logo

15 questions posted

Ask a Question

Usually answered in minutes!

Top Makita Saws Experts

ray gallant

Level 3 Expert

73026 Answers

Brad Brown

Level 3 Expert

18733 Answers

Parson's Repair...
Parson's Repair...

Level 2 Expert

272 Answers

Are you a Makita Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Makita Saws

  • Makita Saws

Most Popular Question

2704 bench saw

  • Saws
Loading...