20 Most Recent Makita 2704 Contractors 15 Amp 10 Inch Benchtop Table Saw - Page 5 Questions & Answers

0helpful
1answer

Hi the battery terminals on my makita lxt circular saw are getting really hot and smells like it's burning any ideas what it could be ?

This might not be the correct answer but it could be that you are working the saw hard and drawing a lot of current from the battery. Make sure your blade is sharp and correct for what you are doing. (Lots of teeth cross cutting, fewer teeth for ripping) and adjust your feed rate. See if that makes a difference.
3/30/2017 6:04:33 AM • Makita Saws • Answered on Mar 30, 2017
0answers
0helpful
1answer

Makita 10" dual slide compound miter saw jerky while moving in and out. What,s wrong?

The pillow block bearing, guide bushings, or even the slide lock mechanism could be the culprit. If you post the model number I can help narrow it down for you.
3/7/2017 11:41:17 AM • Makita Saws • Answered on Mar 07, 2017
0helpful
1answer

How do I wire up a switch on a 110 volt mlt100 makita tablesaw

You can still find inline switch for cords, but make sure they can handle the amperage. A 15A rating should be fine. Don't use a lamp-cord switch, because they are usually rated for much lower current. Some people go to the trouble of mounting an electrical junction box on their machine and routing the cord through it with a light switch. Once again, the light switch must have a higher current rating of 10 or 15 amps, depending on the current-draw of your machine.
2/16/2017 7:43:33 PM • Makita Saws • Answered on Feb 16, 2017
0helpful
1answer

How do I change disk/blade in my Makita PA6 - GF 30.

Thats a material code of Polyamide many products are based on this PA6-GF30 code. like to see here for example Polyamide PA6 GF30 Jacob moeren metrisch WKK Nederland Search on the pictures in Google for the right saw model
2/5/2017 7:02:29 PM • Makita Saws • Answered on Feb 05, 2017
0helpful
1answer

Makita slide compound- Saw Blade. LS0714

It seems as though the original blade was fitted without a spacer. These usually come with any new blade. It is simply a washer (usually aluminium) that fits in the hole of the saw blade and reduces the hole diameter down to the size of the flange on your saw. This is common practice. Never try and centre a blade without the correct size hole to flange size. Very dangerous. These washes are really cheap and can be obtained from most hardware stores. Usually in an assortment of different outside and inside diameters to suit any circumstance. Hope this helps, cheers Bob.
11/16/2016 12:42:10 PM • Makita Saws • Answered on Nov 16, 2016
0helpful
1answer

I think the switch on my petrol cutter is broken how do I replace the switch on my makita cutter

Dismantle the unit, taking photographs as you go and verify that the switch is actually broken (electrically or mechanically). Gain the make and model number of the switch and purchase a new one. Online is probably cheaper. Refitting is the reversal of the dismantle. Cheers Bob
11/16/2016 11:53:35 AM • Makita Saws • Answered on Nov 16, 2016
0helpful
1answer

Makita grinder keeps tripping circut breaker

FIRST OF ALL !! Control where the tool is used first for undervoltage on the mains supply group. If it is everywhere a problem FIRST replace the circuit breaker. After that control all connectors last check interference suppression capacitor. If all are controled , relace armature or electric field or both.
10/12/2016 2:03:33 PM • Makita Saws • Answered on Oct 12, 2016
0helpful
1answer

What kind of fluid, and how do I put it in a makita circular saw model 5177-B

shows up as all electric this may help user manual 16 pages pdf http://www.manualslib.com/manual/98575/Makita-51778.html
5/2/2016 10:45:23 PM • Makita Saws • Answered on May 02, 2016
0helpful
2answers

Makita LS 1000 miter bed does not turn freely; probably jammed up with saw dust. What is the best approach to cleaning the rotating bed?

PDF]TECHNICAL INFORMATION - Makita

www.makita.nl/images/files/onderdelen/nl/LS1020-TE.pdf MAKITA 255mm(10") Miter saw. Models No. Description. New Tool ... Optional accessories. The main specifications are common with #LS1000. Saw blade:.Missing: bed
4/26/2016 7:46:25 AM • Makita Saws • Answered on Apr 26, 2016
0helpful
1answer

I cannot figure out how to install push pin and spring for quick connect assembly

Most cases you mean this type of a special makita sds assembly 25797374-ve3wx4tp2r0ojhvn3hp1125i-3-0.png
3/30/2016 9:20:12 AM • Makita Saws • Answered on Mar 30, 2016
Not finding what you are looking for?
Makita 2704 Contractors 15 Amp 10 Inch Benchtop Table Saw Logo

15 questions posted

Ask a Question

Usually answered in minutes!

Top Makita Saws Experts

ray gallant

Level 3 Expert

73443 Answers

Brad Brown

Level 3 Expert

18805 Answers

Parson's Repair...
Parson's Repair...

Level 2 Expert

272 Answers

Are you a Makita Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Makita Saws

  • Makita Saws

Most Popular Question

2704 bench saw

  • Saws
Loading...