20 Most Recent Makita 2704 Contractors 15 Amp 10 Inch Benchtop Table Saw - Page 3 Questions & Answers

0helpful
1answer

MAKITA L 1016L LOCKED IN BEVEL POSITION

Refer to instructions that came with saw. Big hint page 8. https://cdn.makitatools.com/apps/cms/doc/prod/LS1/897774cd-1c1a-499f-8fa6-bc296110a9d6_LS1016L_IM.pdf
1/23/2019 3:51:42 PM • Makita Saws • Answered on Jan 23, 2019
0helpful
1answer

Is there makita 9553nb service manual

yes there is a can not attached it is to lages
1/19/2019 7:02:32 PM • Makita Saws • Answered on Jan 19, 2019
0helpful
2answers

Makita DCS 540. When you pull the cord it is very hard to pull. It only comes out a few inches. Not enough to start it.

Hi, you might find the cord was broken, and "someone" left it short. remove the pull start unit, look at length of the cord, (take pictures for replacment, noteing direction of cable etc )I guess it should be about one meter long, or spool should be nearly full of cable.Hope this helps you.
1/1/2019 1:16:11 AM • Makita Saws • Answered on Jan 01, 2019
0helpful
5answers

Makita concrete saw dpc7321 won't start has fuel

I'm a retired engineer and work PT as a tool tech for an HD rental ctr.

Compression on a new cylinder/piston is 160 psi. When it drops into the 130~140 psi range the saw becomes hard to start. Below 130 the saw will not run properly and at 90 they are toast. This is mainly due to improper fuel/oil mix (must be one bottle of 50:1 synthetic oil per gallon of regular gas. I use 6 bottles to 5 gallons for addition protection). Because this type of tool works in extremely harsh conditions (concrete dust) it is also imperative to keep the air filters clean. Wash the foam pre-filter after each use with plain water from a garden hose and discard after operating 6 times. Toss away (change with new) the paper filter if dust is present or when changing the pre-filter. Also check the carb hose to the cylinder inlet for cracks. My cost to get a cylinder/piston from Makita runs app. $130. When looking into the cylinder, streaks on the exhaust side indicate improper fuel/oil mix. Streaks on the intake indicate dirty air intrusion.

Good Luck.
12/16/2018 12:57:48 AM • Makita Saws • Answered on Dec 16, 2018
0helpful
1answer

How do I unlock the mikata 10 inch Model ls1030 miter saw

Lower the handle slightly and pull the pin back.
11/19/2018 5:25:04 PM • Makita Saws • Answered on Nov 19, 2018
0helpful
1answer

I have a Makita LS1011 10" sliding miter the carriage will not raise and lower easily very hard lifting it up or down what can i do to fix this

This is usually caused by the linkage that operates the guard assembly. Check to make sure it operates freely Makita LS1011 Parts List and Diagram eReplacementParts com Reference #62 and the bushing that rides inside it #55 The link usually wears out and the bushing hangs up making the saw difficult to raise and lower.
10/18/2018 11:38:27 AM • Makita Saws • Answered on Oct 18, 2018
0helpful
1answer

My makita jig saw hops while cutting perspex what could be the problem

Check that you've installed the right blades. There are blades that cut on the upward stroke and on the downward stroke. Downward cut blades will kick like crazy. Also make sure the perspex is supported as best as possible to stop it from trying to flex with the stroke of the jigsaw.
10/17/2018 4:50:07 AM • Makita Saws • Answered on Oct 17, 2018
0helpful
1answer
0helpful
1answer

Where is the reset on a makita table saw

If this is a direct drive usually nearby the on/off switch, if not look around the motor near the capacitor opposite of the pulley. good luck.
10/2/2018 1:31:18 AM • Makita Saws • Answered on Oct 02, 2018
0helpful
1answer

I have a makita dss611 saw that has just stopped working

It could be 1 of the 2 carbon brushes when the autostop protection is activated replace carbon brush cb441 194435-6 is a normal problem when the working hours are arrived ,but if your battery is empty it will stopping at once a protection for li-ion deep discharge protection. Li ION is the best to have allways 1 of the batteries on the charger ,if working and do not full unload it change after a while before its stopped its better for the expensive li-ion batteries but if forget one batterie to use over time ( because you want to save him well-intentioned ) to use it frequently is better when its to deep discharged it will not working anymore the charger will not accept the battery anymore if its deep discharged , to rewake it preloading it only like this way a safe as possible against fire hazard not use chargers of cars or other tricks do a full working loaden battery from the charger and connect with that other battery connect both to each other with 2 1,5 kwdr wires the full battery with the not accepted not working deep discharged battery that was forget for a long time BEWARE to do only connect a polarisation as the + to the + and the - to the - the poles parrallel connect to each other not longer then 3 minutes after that remove the wires and now put immediately the not working battery on the charger and see that its accepted again, if its not working repeat it one time again , not for 3 times its a real battery problem for garantee or replacement do not work on li ion with battery chargers for a car or other full overpowered chargers without knowledge do not open or disconnect wires inside the battery then the Makita battery is immediatly dead . because of fire hazard protection li ion full battery on empty battery + to + - to - not more then 3 minutes if it still not working within 3 minutes repeat it once again be shure the wires are connected correct from battery to battery to preload if there was an battery problem of an empty battery or dead battery.
8/17/2018 6:27:18 PM • Makita Saws • Answered on Aug 17, 2018
0helpful
1answer

Anyone know how to adjust a Makita ls1216 mitre not bevel presets? My 0 degree mitre is spot on. But my 45 degree mitre preset is off my 1/4 degree.

check for slide wear on the mounts if it has any it allows the motor and saw to drop sideways and alter the cut angle you can compensate by moving the setting that bit extra and the locking it up
8/1/2018 9:56:09 AM • Makita Saws • Answered on Aug 01, 2018
0helpful
1answer

Makita LS1216L brake not working at all. New brushes put in two weeks ago and they are already shot too. Would this more likely be the armature or field or both or something else?

The brake on your mitersaw is an electric brake. When you release the power switch, the switch sends current to a brake coil in the motor's field. This reverses polarity to the motor and stops the armature from spinning. Good contact from the motor brushes is also important for this to work correctly. The most common issues with a mitersaw brake are the brushes, part number,CB-154 , and the switch part number, 650618-3. It is less common but a damaged field can also make the brake not work correctly. It is part number 596356-2. https://www.ereplacementparts.com/makita-ls1216l-1234-dual-slide-compound-miter-saw-parts-c-97_98_99_40150.html
5/30/2018 2:23:36 PM • Makita Saws • Answered on May 30, 2018
0helpful
1answer
0helpful
1answer

My Makita blower will only run when its on its side, when you put it upright it cuts out, put it on its side its start without any problems, any ideas??

Too short carbon brush problem or electric field contacts or safety contact for pipe connection, only a loose contact somewhere.
5/15/2018 4:06:46 PM • Makita Saws • Answered on May 15, 2018
0helpful
1answer

Wiring diagram for switch on makita mlt100 saw

ring Makita on 01908 210710 and ask for technical
3/29/2018 9:14:41 PM • Makita Saws • Answered on Mar 29, 2018
Not finding what you are looking for?
Makita 2704 Contractors 15 Amp 10 Inch Benchtop Table Saw Logo

15 questions posted

Ask a Question

Usually answered in minutes!

Top Makita Saws Experts

ray gallant

Level 3 Expert

73443 Answers

Brad Brown

Level 3 Expert

18805 Answers

Parson's Repair...
Parson's Repair...

Level 2 Expert

272 Answers

Are you a Makita Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Makita Saws

  • Makita Saws

Most Popular Question

2704 bench saw

  • Saws
Loading...