20 Most Recent Craftsman 10" Table Saw Questions & Answers

Model 113 226880. Where can I get a wiring diagram for on/off switch?

Why do you need a wiring diagram ,is the saw not working .
If its single phase then there's usually only the live wire going through the switch with a feed to the capacitors if fitted.

Craftsman 10"... | Answered on Jul 11, 2019

1 Answer

Want to replace under powered saw motor on sears 10"table saw

u can put a 2 and above if u want just need to have the correct rpms

Craftsman 10"... | Answered on Sep 04, 2018

2 Answers

10 inch table saw blade not square with table

Sounds like the bolts that hold the motor assembly on the table may be loose allowing the blade assembly to move. Look underneath the table and clean out all the dirt and loosen all the hold down bolts and realign the blade and tighten back up.

Craftsman 10"... | Answered on May 29, 2018

1 Answer

I have an older model Craftsman table saw that the

If it is locked by rust you can get some heat onto it and the expansion will break it free. Make sure any solvent in the freeing agent you put on has evaporated or you may loose your eyebrows. Get a pencil flame blow torch (larger flame if there is sufficient space) protect any components which could be damaged by shielding with a soldering mat. Heat up the seized joint. It doesn't need to be to extreme temperature. Use a jet of cold water to chill the seized joint. Check to see if it has freed, if not repeat the procedure until it does. Once free, heat gently to dry it and then apply lubrication once it has cooled.

Craftsman 10"... | Answered on Jan 11, 2018

3 Answers

While ripping 1x4's my 10 inch craftmens saw stopped running. Pushing in on the reset button doesn't help. After 2-3 minites saw will start up again. I'm not forcing the boards and overwor

the thermal motor relay is shutting it down,,motor to hot,
insure that all the air vents or saw housing are not full of saw dust. blow it out with air from a reversed hose on a shop vac if you don't have a compressor.
hope this helps.

Craftsman 10"... | Answered on Jan 03, 2018

1 Answer

Question on craftman table saw S292.

Put the model number (it'll be something like "123.3321") in the Google search bar and you'll find a manual for download. Then list on Craigslist and you'll be rid of it quickly!

Craftsman 10"... | Answered on Oct 28, 2017

1 Answer

Bosch table saw 4000 reverse threaded blade nut?

If you want the tool to enter the wood in some specific angles then this is what you can use.
http://sharp.reviews/

Craftsman 10"... | Answered on Sep 28, 2017

1 Answer

Hi - I'm looking for a manual for a Craftsman

hello there try ebay or gumtree or amazon ok

Craftsman 10"... | Answered on Sep 24, 2017

1 Answer

Shaft lock will not hold cant change blade

Generally yes. Just put a screwdriver or bar of metal into the teeth of the blade and crank the nut. In the old days that was how we did it all the time.

A vicegrip can be clamped on the blade if you want to protect the teeth.

Craftsman 10"... | Answered on Jun 05, 2017

1 Answer

Craftsman saw mod # 113-298051

The blade is able to be set to different angles by the handle under the front edge of the table. There is a lock handle to keep the angle set correctly. Loosen the lock handle, press a square (90 degree tool) against the flat of the blade - not the teeth - then lock the blade in place.

Craftsman 113 298051 Owner Manual rr

Craftsman 10"... | Answered on Jun 05, 2017

1 Answer

HOW DO I REMOVE MOTOR FROM CRAFTSMAN 10 INCH TABLE SAW MODEL # 137.218250

Craftsman 137 21825 Owner Manual
Although it is not the exact manual, it may be close enough to enable you to remove and replace the motor assembly.

https://www.manualslib.com/manual/32803/Craftsman-137-21825.html

Craftsman 10"... | Answered on Jun 05, 2017

2 Answers

How do i wire the motor mode 370200 for 110V

http://www.shopyourway.com/questions/1219023

Craftsman 10"... | Answered on Jun 23, 2016

1 Answer

113 298030 parts manual

Sears Parts Direct has the manual and parts diagrams for the 113.298030 here: http://www.searspartsdirect.com/model-number/113298030/0247/0744600.html . The direct link to the Owner's Manual is http://c.searspartsdirect.com/mmh/pd_download/lis_pdf/OWNM/L1001152.pdf .

I hope this helps.

Cindy Wells

Craftsman 10"... | Answered on Jun 06, 2016

2 Answers

Fence is out of alignment and I am not sure how to

There is a couple of screws holding the fence perpindicular to the front guide. loosen slightly, square up fence and retighten screws.

Craftsman 10"... | Answered on Jan 19, 2016

1 Answer

I need the wiring diagram for my 10 table saw

Im guessing ... the motor is 110 volt AC (AC dont care if it is coming or going) ... find the two terminals in the motor and hook the wires back up. If it HAPPENS to be incorrect, the saw will run poorly or the overload will trip.

I wouldnt be afraid to use this method on my craftsman table saw.

Craftsman 10"... | Answered on Dec 14, 2015

1 Answer

Model number 137228210

Yes just make sure you have or make a new clearance plate to allow the dado to come thru

Craftsman 10"... | Answered on Oct 13, 2015

1 Answer

Craftsman owners manuals

You may be able to get one from Sears Online In Store Shopping Appliances Clothing More or google the manual and many websites offer them. Good luck.

Craftsman 10"... | Answered on Jul 04, 2015

2 Answers

Where can I find replacement parts in Canada for old Craftsman 10" Table saw?

Since you are in Canada, you will need to go to http://www.sears.ca/content/specialty-services/parts-and-service. There you would create an account and login to search for the parts you need. The person at Sears Parts I chatted with strongly suggested that you call the Canadian Sears Parts Direct to place your order. The phone number is 800-361-6665. To save you some time I confirmed with Sears Parts U.S. that part# 202N for your saw model 137271320 is available. Here is a link that should show you a picture of the saw http://s.sears.com/is/image/Sears/PD_0009_137_14912201B9?wid=2000. I was quoted a price of $34.03 U.S. including shipping. Not sure what you will have to pay in Canada. Good luck in your search.
http://s.sears.com/is/image/Sears/PD_0009_137_14912201B9?wid=2000 Parts and Service Sears ca parts

Craftsman 10"... | Answered on May 14, 2015

0 Answers