Top 20
Dremel & Stylus Lithium Ion Cordless Rotary Tool Questions & Answers
Dremel Stylus charging
Even in 2018 this is still correct. Change the Capacitor and runs OK
I have put a 50 v to make sure this never happens again
Short run period
Please help. Because l am in Australia l can't phone the tecnition and the link to get the manual doesn't go any where, neither does the dremel website, nothing happens, and every time l try to do something in this site l get catapulted back to the begining of the page. Frustrating! Can someone help me with the manual?
Stylus motor make terrible noise
Take it back to the store, explain your problem. Like as not, they will exchange it. My experience with this tool tells me that it is a noisy unit. Depending on the material you are working and the stylus you are using, the noise will change.
Dremel 1100 for in a few seconds
Change the capacitor 220uF 25V and it will charge properly again (at least that is the result I got and several others here at FixYa).Easy to do and cheap (component around 0,2 Euros) work about 2 min,.
Dremel Stylus only charges for 2-3 minutes then
This is the charger, its getting a reading from the battery that its charged when it isn't. I don't know exactly how that charger is wired but, to be suroe it is the charger, as I have had similar problems beforehand.
Picked up a stylus yesterday.
the manual that came
Hi Les,
Dremel .com has a lot of information and a video that explains what the buttons do. Changing bits you just turn the chuck and push a button and then loosen the chuck and the bit and collet will come out.The red stuff is rouge and is used for polishing with the felt wheels and points, there is a shaft with a screw that the points are used with.I copied the owners manual but don't know if it will open.There are phone # for questions.THANK YOU for choosing FixYa.com.................Darryel
Contact the Dremel Experts for additional assistance
DOWNLOADSDREMEL STYLUS™ LITHIUM-ION CORDLESS OWNER'S MANUAL
Request Literature
Submit a question
Dremel Stylus 1100 7.2 volt wont charge when the
My stylus is doing exactly the same thing. l was advised by numerous people to change the capacitor in the charging dock, they also said that you can find youtube videos to guide you through it (the capacitor only cost a few cents when l bought it). I really should finish doing that job, although l did actually remove the 'screws'' from the base, l warn you- they are triangle and a nightmare to unscrew, see if you can find a triangle screwdriver BEFORE you start, or you'll end up doing what l did and destroying a perfectly good straight screwdriver!??. Good luck
Dremel Stylus model 1100
Change the capacitor 220uF and it will most certainly work again. I got the idea from FixYa and it solved my problem!Easy to change just 2 soldering points and a component costing around 0,2 Euros. If you do not know how to operate a soldering tool ask someone for a quick assistance. The switch takes around 2 min (1,5 min to open the charger and 0,5 min to change the component!)./Johan
I'm not sure if I am setting the collet properly- Some step-by-step instruction needed.
I just looked at an owners manual at Dremel.com (64 pages) and under tightening the collet they state to finger tighten and then use wrench making sure to not overtighten. All you really need to do is snug the wrench up enough to hold the accessory. after tightening or loosening release the lock button and I always turn mine by hand making sure not to hit switch or remove battery (suggested for removal/installation) to ensure the release isn't catching. You can look at the manual and other information by going to their site. They also have a toll free number to talk with a tech for help. If I have helped you would you please rate this response accordingly. Thank you
Tool inserts wabble
sounds like the head of the Dremel is bent. you should take it back and get a diffrent one.
Looking for the service manual for a weller mini shop model 601 Dremel tool
I'm sorry, but I don't have access to specific service manuals for individual tools. However, here are some steps you can follow to find a service manual for your Weller Mini Shop Model 601 Dremel tool:
- Visit the Weller website: The Weller website may have a library of manuals for its products, including the Mini Shop Model 601.
- Check the manufacturer's support page: Most manufacturers have a support page on their website where you can find user manuals, FAQs, and other resources.
- Search online: You can also try searching online for a digital copy of the manual. Websites like ManualsLib and ManualsOnline may have the manual you need.
- Contact the manufacturer: If you're unable to find the manual online, you can contact the manufacturer directly and request a copy. You may need to provide your tool's model number and other information.
I hope this helps you find the service manual for your Weller Mini Shop Model 601 Dremel tool.
Not finding what you are looking for?