20 Most Recent Dremel & Stylus Lithium Ion Cordless Rotary Tool - Page 2 Questions & Answers

I just looked at an owners manual at Dremel.com (64 pages) and under tightening the collet they state to finger tighten and then use wrench making sure to not overtighten. All you really need to do is snug the wrench up enough to hold the accessory. after tightening or loosening release the lock button and I always turn mine by hand making sure not to hit switch or remove battery (suggested for removal/installation) to ensure the release isn't catching. You can look at the manual and other information by going to their site. They also have a toll free number to talk with a tech for help. If I have helped you would you please rate this response accordingly. Thank you

sounds like the head of the Dremel is bent. you should take it back and get a diffrent one.

I'm sorry, but I don't have access to specific service manuals for individual tools. However, here are some steps you can follow to find a service manual for your Weller Mini Shop Model 601 Dremel tool:

1. Visit the Weller website: The Weller website may have a library of manuals for its products, including the Mini Shop Model 601.
2. Check the manufacturer's support page: Most manufacturers have a support page on their website where you can find user manuals, FAQs, and other resources.
3. Search online: You can also try searching online for a digital copy of the manual. Websites like ManualsLib and ManualsOnline may have the manual you need.
4. Contact the manufacturer: If you're unable to find the manual online, you can contact the manufacturer directly and request a copy. You may need to provide your tool's model number and other information.

I hope this helps you find the service manual for your Weller Mini Shop Model 601 Dremel tool.

Question edited for clarity. Question moved from Rotary Club International :>D Dremel don't make Craftsman Rotary Tools https://www.google.com/search?q=does+dremel+make+craftsman+rotary+tool& Decide if you have a Dremel or a Craftsman and Google simply make model parts ..

Question edited for clarity, spelling of Dremel. Question moved from Cameras Category. How to strip and replace the locks. https://www.google.com/search?q=Dremel+4200+and+the+blue+unlock+tabs+are+stuck+on+unlock ..

Model of dremel, battery or mains powered?

Try using the correct collet size

Look at the clogged teeth on the blade. Copper does that. Use a pair of tin snips.

There is a coupling between the drive motor and the chuck. You will need to take the tool apart to replace it. E-bay has these.

It will be under warranty if just bought it , if faulty it will be repaired or replaced at no cost to you .

https://www.eternaltools.com/blog/complete-guide-to-your-dremel-rotary-tool https://www.eternaltools.com/felt-polishers https://us.dremel.com/en_US/products/-/show-product/tools/684-01-cleaning-polishing-accessory-set

The flashing light indicates an error, possibly your battery is shot or malfunctioning. New battery needed.

There might be many reasons but the one of them is you might be obstructing its air intake passage and it is over-heating.

If the threads on the nut or shaft are stripped, the nut will turn freely and it can be removed with pliers by turning and pulling at the same time. If it won't turn, it is probably galled or cross-threaded. In that case, try penetrating oil first. If that doesn't loosen it, try heating the nut with a butane or mapp gas torch. Good luck.

your best bet will be ebay Then if that's not successful, check with these people https://www.ereplacementparts.com/search_result.php?q=Charger%2C+dremel+1100 You'll need to know the voltage. The 100 volt charger is discontinued. They carry authentic Dremel parts.

https://all-guidesbox.com/model/dremel/850.html https://www.dremel.com/en_US/support/manuals https://www.dremel.com/en_US/support/manuals/other-tools

You screw off the collar on the tool, remove the chuck and inner part. The chuck is replaced with a special chuck (no inner piece). The special chuck has a square opening in it's nose that accepts the square end of the flex shaft inner cable. Is is actually a speedometer drive cable, from yesteryear. Then you pull the inner cable out slightly, if it will, and put the inner cable into the square opening of the special chuck on your dremel motor. once engauged, you carefully screw the outer shaft housing on to the end of your dremel motor. What you want to avoid is damaging this area during flex shaft assembly. I have had success with turning the output side of the flex shaft, while tightening the outer flex shaft onto the dremel motor. Stop tightening if it starts binding... Rotation seems to help with alignment of all parts. Cheers, Doc

spray lube or oil and use pliers to move it back and forth