20 Most Recent Stanley Utility Knife - Page 2 Questions & Answers


HI!Kindly pull the button on the end of the knife and then after you remove that you can now put the blade of your knife.

Stanley Utility... | Answered on Aug 21, 2011


This is the closest thing I can find. Click here.
Otherwise, write Stanley support and they'll answer you here.

I hope this information allows you to resolve this issue. If you need further assistance, please post back with a comment to this thread.
If I've managed to answer your question or solve a problem, please take just a moment to rate this post....thanks!

Stanley Utility... | Answered on Jul 07, 2011


there is a little black button on the end where the blade comes out. With the blade in the out position,push in the button and pull out the blade. With button pushed insert new blade or turn the old one around to use the other end.let go of the button and you are ready to go.

Stanley Utility... | Answered on Jun 26, 2011


Hi.

See here the Stanley knife disassembly. If you have a 99E there may be an additional plastic part that is not shown in the diagram. The plastic tab is located at the back of the blade.

Stanley Utility... | Answered on Jun 04, 2011


This knife is ****. To load... you have to push the slide all the way forward. Make sure the switch is set to unlock. PINCH THE BLADE WITH YOUR FINGERS AND WIGGLE IT INTO PLACE. Then you have to use every ounce of thumb power to relock the switch.

Once you are done, the blade will still come out in 9.9 / 10 times you cut something.

Stanley Utility... | Answered on May 28, 2011


the blade section pivots to swivel when doing that it allows you access to the blade storage area that holds up to 7 blades, if the extra blades arent in place perfectly the handle won't close properly, if your problem is with the blades themselves, make sure that the slot in the blade is aligned with the holder perfectly

Stanley Utility... | Answered on May 14, 2011


At the back end of the knive (the curved end) press the black piece through the yellow rounded part and the yellow front and the black back will part, now slide the yellow part back to reviel the blade folder. Fit new blade then refit the yellow part on top of the black part and slide the yellow part foward to lock it back in.

Stanley Utility... | Answered on Jul 31, 2010


I was able to find the answer on another site. It is really simple when someone tells it to you. You push the blade all the way out then you can push the yellow button and it comes out.

Stanley Utility... | Answered on Sep 07, 2009


Slide the blade holder all the way out, press on the tab as shown in picture. Pull on blade with other hand. Blade slides right out.
10_12_2016_7_08_24_am.jpg

Stanley Cutter... | Answered on Jun 07, 2017


you can use a portable bandsaw to cut rebar, I find it to be the best solution when I can't take the rebar somewhere to cut it. But be careful if the metal is heavy it could fall and dent/damage the floor if you're working indoors of cause injury should it land on you.

Cutter Tools | Answered on Sep 20, 2019


Use a third blade, preferable mounted to your utility handle, to part them. Handle only from the back side and give the utility knife a slight twist as soon as it is between the points of the new blades.

Cutter Tools | Answered on Sep 13, 2019


Manual bolt cutters usually have symmetrical V-edge cutting blades.
knife-edge-styles3-uipjjaq4o2dp2d2150uxp5lp-5-5.png
With the sharpening angle in the range of 20-30 degrees.

28bc-7-4-_tbi-_head_on_centre_cut_replacement_jaws-uipjjaq4o2dp2d2150uxp5lp-5-9.jpg
For comparison, the sharpening angle of the kitchen knife is less than 10 degrees.

With such a pretty blunt edge is impossible to cut your finger. But this is the best option for cutting thick metal rods or cables. Like this:
bolt-cutter_3-uipjjaq4o2dp2d2150uxp5lp-5-14.png
If it is interesting to read more information about bolt cutters, I recommend this review -
https://toolslaboratory.com/best-bolt-cutter-buyers-guide-2019

Cutter Tools | Answered on Jul 10, 2019

Not finding what you are looking for?
Stanley  Utility Knife  Logo

49 questions posted

Ask a Question

Usually answered in minutes!

Top Stanley Cutter Tools Experts

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

Joe Garcia
Joe Garcia

Level 2 Expert

210 Answers

JOHN LAPIER

Level 3 Expert

2601 Answers

Are you a Stanley Cutter Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Stanley Cutter Tools

  • Stanley Cutter Tools

Most Popular Question

change blade in stanley fatmax

  • Cutter Tools
Loading...