20 Most Recent Mtd LAWN MOWER PART # 983-04162A-0638 DECK Assembly:SD 42" W Questions & Answers


i need a diagram showing for a 20hp yardman tractor model number 13AT605G755

Mtd LAWN MOWER... | Answered on Apr 09, 2019


PartsTreeRepairClinic may have a video

Mtd LAWN MOWER... | Answered on Mar 06, 2018


Try PartsTree repair clinic

Mtd LAWN MOWER... | Answered on Jan 21, 2018


PartsTreerepairclinic

Mtd LAWN MOWER... | Answered on Jan 21, 2018


SearsPartsDirect.com

Mtd LAWN MOWER... | Answered on Jan 21, 2018


SearsPartsDirect may help

Mtd LAWN MOWER... | Answered on Jan 20, 2018


Contact MTD if your manual doesn't cover this, or buy a shop manual.

Mtd LAWN MOWER... | Answered on Dec 22, 2014


Contact MTD if your manual doesn't cover this, or buy a shop manual

Mtd LAWN MOWER... | Answered on Dec 22, 2014


Hi,have just bought one and the number of the one which arrived is as follows #cama heavy duty belts part No.78-3896

Mtd LAWN MOWER... | Answered on Jan 27, 2013


Hi there. The only thing I can suggest is to download your manual at http://www.mtdproducts.com/webapp/wcs/stores/servlet/OwnersCenterView?storeId=10500&catalogId=20500&langId=-1 It will show how the belts are routed. Hope this helps

Mtd LAWN MOWER... | Answered on Jun 04, 2011


Hi naputi4wash...

Remove the spark plug and hook the wire to it and ground it to the mower and crank to make sure you are getting fire/spark at the plug, if yoiu are getting fire then do the following:
Check/Clean/Replace your fuel filter if you have one.
If the mower/weedeater is over a couple of years old, then I recommend that you buy and install a new carburetor repair kit,because the diaphragm will get hard and that will cause it to be hard to crank.
Sounds like you will need to clean the carburetor or replace your carburetor internal rubber parts like the diaphgram and O rings.
Be sure to use compressed air to blow out all the fuel and air passages.
Be careful when blowing out the passages, because there are sometimes small rubber type seats in the bottom of some of the passages.
Sometimes you can get by with priming the carburetor or using starting fluid and letting it run a few times like that and it will flush the gunk out of the jets,but most of the time you will need to rebuild the carburetor.
Keep in mind that the float for the carburetor must be level when you go to reassemble the carburetor or follow the instrucitons you get with the carburetor kit.
When you clean your carburetor and remove the jet screws, you will first need to lightly seat the jet screws.
But before you lightly seat the jet screws count the number of turns it takes to seat the jet screws from their original position.
Be sure to mark the turns down on a piece of paper.
That way when you put the jets back in, you know to lightly seat them first and then turn them back out to their orginal position before you started.
This is a FREE answer,Please rate me

Mtd LAWN MOWER... | Answered on Apr 22, 2011


need main drive belt numbers for 132-520c6701L212G60073 10.5 horse power

Mtd LAWN MOWER... | Answered on Jan 07, 2011

Not finding what you are looking for?
Mtd LAWN MOWER PART # 983-04162A-0638 DECK Assembly:SD 42" W Logo

28 questions posted

Ask a Question

Usually answered in minutes!

Top Mtd Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

dannydoesita

Level 3 Expert

777 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Mtd Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mtd Garden

  • Mtd Garden

Most Popular Question

cannot put belt back

  • Garden
Loading...