Black & Decker BDL400S Bullseye Crosshair 90 Degree Auto Leveling Interior Line Laser - Answered Questions & Fixed issues

0helpful
1answer

There is a micro-fine, almost

The two very fine red wires connect here. black & decker-kd0ysdieigozt2ge0gqdsflt-3-0.jpg
4/16/2017 6:27:14 AM • Black & Decker... • Answered on Apr 16, 2017 • 705 views
0helpful
1answer

Black and decker crosshair laser level

The really fine wire is soldered from the RED terminal on left to the RED terminal on the top left (underneath the board). See below in the images. black-decker-crosshair-laser-level-2bsxhpa3po2xrabjzw4jy444-1-0.jpg black-decker-crosshair-laser-level-2bsxhpa3po2xrabjzw4jy444-1-2.jpg
3/30/2015 2:16:08 AM • Black & Decker... • Answered on Mar 30, 2015 • 1,723 views
0helpful
1answer

The laser light on my black & decker bdl500 stopped working

I had the same problem with mine. I took it apart and inspected it. Mine was a loose connection and after some fiddling with the wires the laser came back on. Put it back together and haven't had a problem with it since. Hope it helps.
3/30/2015 1:40:56 AM • Black & Decker... • Answered on Mar 30, 2015 • 1,577 views
0helpful
1answer

Do you have a manual for this product Black &

2/21/2015 7:42:33 PM • Black & Decker... • Answered on Feb 21, 2015 • 192 views
0helpful
1answer

How do i calibrate a black & decker BDL220S laser level

Rotate the laser to center horizontal (H) or vertical (G) bubble vials
9/11/2022 3:59:12 PM • Black & Decker... • Answered on Sep 11, 2022 • 41 views
0helpful
2answers

I have a BDS 300 sensor and have lost instructions

I just bought one too and instructions need deciphering. Select wood or metal with selector switch. Put unit flat against wall. Press and hold on/off button on left. (It looks like it must be kept pressed in at all times to be 'on' and when released it's 'off). The unit with calibrate and give a beep back and lower red LED will stay on. Move unit slowly left/right and more red LEDs light up until green is on. This is 1st edge. Mark it with pencil. Move unit along until Green is off and down to single LED. Then move it back in opp. direction until Green is on again. This is 2nd edge. Attached is a scan of page from Instruction Manual. Quality is lowish as attachment limit here is 150kb.e4edea4.jpg
1/29/2013 10:11:15 PM • Black & Decker... • Answered on Jan 29, 2013 • 8,081 views
0helpful
1answer
0helpful
1answer

I have no laser light when I turn my level on

Check to make sure battery isn't bad first.. If upon changing the battery, it still doesn't work, the laser might be bad or worn out. Good luck... HDTV GURU JAY
3/16/2011 1:51:44 PM • Black & Decker... • Answered on Mar 16, 2011 • 280 views
0helpful
1answer

CHarging light blinking while trying to charge

Battery is old...time for a new one.
9/3/2009 5:12:36 PM • Black & Decker... • Answered on Sep 03, 2009 • 220 views
0helpful
1answer

I have a Digitech XC0436 Weather Station.

Remove the batteries from both units for a couple of hours. Replace the indoor unit battery and then the outdoor battery. This will effect a reset of sorts. Don't forget your rainfall can be different to someone 600 meters away. Having said that 100mm / 4 3/4" difference is a lot.
1/28/2023 11:26:55 PM • Measuring Tools... • Answered on Jan 28, 2023 • 18 views
0helpful
1answer

Envirastation dws400 main unit displaying HH for outside temp

How do I get my envirostation 400 to stop beeping or stop changing the channel
1/25/2023 4:59:59 AM • Measuring Tools... • Answered on Jan 25, 2023 • 146 views
0helpful
1answer

34788 Recover does not work

"Recover" is a term that can be used in various contexts, can you please provide more information on what you are trying to recover and what is the specific issue you are facing? If it is a software issue, please specify the software and the operating system you are using. Also, please provide more information on what you mean by "does not work", is there an error message or any other symptom that you are experiencing? This information will help me understand the issue better and provide a more accurate solution.
1/15/2023 8:03:52 AM • Measuring Tools... • Answered on Jan 15, 2023 • 27 views
0helpful
1answer

How to set electrode on pilot for empire rh50b

  1. Turn off the gas supply to the heater.
  2. Locate the pilot assembly on the heater. It is usually located near the bottom of the unit.
  3. Remove the pilot shield, which is typically a metal or plastic cover that protects the pilot assembly.
  4. Locate the electrode, which is a small metal rod that is located near the pilot burner.
  5. Adjust the position of the electrode so that it is directly in front of the pilot burner, with a distance of 1/8 inch to 3/16 inch between the electrode tip and the pilot flame.
  6. Replace the pilot shield and turn the gas supply back on.
  7. Test the pilot flame to ensure that it is stable and blue in color.
1/12/2023 8:20:34 PM • Measuring Tools... • Answered on Jan 12, 2023 • 21 views
0helpful
1answer

My figure has DigiTech XC-0366 wireless weather station is not collecting the outdoor temperature

Your 'figure'?? Normally it has to be done in order. Remove both lots of batteries. Put the base unit batteries in first and then put in the outside unit batteries. they should pair. In fact the manual states that. Instructions: - Open the battery compartment on the weather station and insert 2 x AA batteries, taking care to put them in the correct polarity. Close the battery compartment. - Open the battery compartment on the transmitter and insert 2 x AA batteries, taking care to put them in the correct polarity. Close the battery compartment. Note: Ensure to install the batteries into the weather station and transmitter within the same hour to ensure that they synchronize properly.

DigiTech XC-0366 User Manual - ManualsLib

https://www.manualslib.com > ... > Weather Station View and Download DigiTech XC-0366 user manual online. Wireless Weather Station With Outdoor Sensor. XC-0366 weather station pdf manual download.
1/8/2023 5:53:43 AM • Measuring Tools... • Answered on Jan 08, 2023 • 30 views
0helpful
4answers

What is hookah?

A hookah is an instrument used to smoke shisha. Shisha is a type of flavored tobacco! Read more on Shisha Heart
1/5/2023 10:15:42 AM • Measuring Tools... • Answered on Jan 05, 2023 • 1,223 views
0helpful
1answer

Sokkia Total sation getting the error message E123 & E124. What is the problem.

The error messages E123 and E124 on a Sokkia total station typically indicate a problem with the instrument's distance measuring system. This could be caused by a number of issues, including problems with the instrument's internal hardware, issues with the reflector being used, or problems with the environment in which the instrument is being used. To troubleshoot this issue, you could try the following steps:
  1. Check the instrument's settings and make sure that it is configured correctly.
  2. Check the reflector being used and make sure that it is clean and properly aligned.
  3. Make sure that the instrument is being used in an appropriate environment. For example, it should not be used in extreme temperatures, high humidity, or in the presence of strong electromagnetic interference.
1/2/2023 5:00:48 PM • Measuring Tools... • Answered on Jan 02, 2023 • 19 views
0helpful
1answer

Stanley Fatmax 1000 Peak Amp Power Station. Where can I buy an O ring for a Fatmax 1000A?

You can buy O-rings by size from Home Depot, Hardware stores or any automotive outlet. https://www.google.com/search?q=Fatmax+1000+parts ..
11/18/2022 8:14:13 PM • Measuring Tools... • Answered on Nov 18, 2022 • 27 views
0helpful
1answer

How do I calibrate a Digitech rain gauge. It is reading too high.

Question edited for clarity, two questions made into one. Question moved from Digitech Music to Weather Station Duplicate post deleted in Cars and Trucks. Refresh page to see your question published. Help in the link. All of the weather stations are made by the same company. https://www.google.com/search?q=calibrate+a+Digitech+rain+gauge ..
11/18/2022 7:51:15 PM • Measuring Tools... • Answered on Nov 18, 2022 • 29 views
Not finding what you are looking for?
Black & Decker BDL400S Bullseye Crosshair 90 Degree Auto Leveling Interior Line Laser Logo

Popular Tags

9 questions posted

Ask a Question

Usually answered in minutes!

Top Black & Decker Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

19166 Answers

Tom Chichester

Level 3 Expert

62329 Answers

ADMIN Andrew
ADMIN Andrew

Level 3 Expert

55739 Answers

Are you a Black & Decker Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...