Reebok 8700 ES Treadmill - Silver Service Delivery! at GNC - Answered Questions & Fixed issues

Step 1:

1) Please NEVER use extension cord, this will bring dangerous spikes, glitches, that will affect to your treadmills.Disconnect it and use the specific outlet wall, for your machine2) I recommend that you use the Software calibration for easy diagnose, troubleshooting and fix it. This will be clear the information code appearing the display. Go ahead

Step 2:

The Steps for Newer Style Console Calibration:

1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

10. Press ENTER. You should see "SS" or "55" in the console.

11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Step 3:

how do i replace the drive belt on8700es

it should have came with the machiene

I had the same problem happen today!! I called 188-999-3756, they are sending my a new panel for 5.95! Yes, I bet that many owners of this treadmill have had the same thing happen. Mine is only 8 months old! let me know if you get this message.

I just bought the same thing from sams club and am having the same problem.....I can't even get mine to turn on! Can anyone help?

it needs service the motor current is to high and jammped. due to bad belt parts or the motor itself , a tech with turn the parts by hand to see if they or what is jammed. or gear box there. get it fixed ? ok:

E2 Error usually indicates that the treadmill is overloaded and applies to various models like TR150, TRX1000 and TR 200. To fix this problem, check if your treadmill motor is overheating. Signs of an overheated motor include; grinding noise, motor produces a burning smell and inconsistent operation speeds.

Treadmill repair : r/fixit

Reddit · r/fixit 3 comments · 4 years ago Hi i have a reebok one gt30 treadmill bought in 2016. Recently at ... Start googling error codes and find out what E2 means. Upvote 2 Which part of my broken treadmill should I try replacing? - Reddit Apr 18, 2020 Urevo 2-in-1 giving e10 error message- did you encounter this ... Oct 10, 2022 Need help with Sole F63 treadmill error code - Reddit Nov 21, 2022 More results from www.reddit.com

Reebok jet 300 treadmill e02 error - motor output dc is 11v on ...

All About Circuits https://forum.allaboutcircuits.com > threads > reebok-j... Jan 9, 2023 - It seems to me to be a problem in the circuit that gives feedback to the processor about the voltage in the motor, error02 and does not arm the ... Missing: GT30 ‎' Show results with: GT30

Treadmill Support - Reebok Fitness

reebokfitness.info https://www.reebokfitness.info > treadmill-support View user manuals, assembly guides, instruction books, and technical support videos for all Reebok treadmills, including how to reduce static shock. ..

f the E13 error code is still showing after restarting your treadmill, check to ensure that the wiring between the AC motor drive and motor cables is securely connected. If any of the cables/connectors appear loose, completely power off and unplug the treadmill before unplugging and reattaching the cables.

https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=&cad=rja&uact=8&ved=2ahUKEwj79pDHxZSCAxV_AHkGHbhiDxkQFnoECBsQAQ&url=https%3A%2F%2Fwww.justanswer.com%2Ffitness-equipment%2Fgdah0-reebok-8000es-treadmill-incline-keeps-going.html&usg=AOvVaw0mEH-BLg44uwLpy6jJGb3K&opi=89978449

The reverse of assembly as shown in the manual https://www.scribd.com/document/82118881/REM11300-Power-Run-Treadmill https://www.google.com/search?q=Reebok+Treadmill+Powerrun+11300+assembly ..

Check the incline motor: If resetting the treadmill doesn't work, it's possible that the incline motor is faulty and needs to be replaced.

Here is the assembly instructions. I doubt an extractor is needed. https://cdn.sweatband.com/upload/multimedia/RE1-11810-ZR8%20CROSS%20TRAINER%20ASSEMBLY%20GUIDE.pdf Assembly video. You will be working in reverse. https://www.youtube.com/watch?v=6cA7cbsYr_I Threads will be metric fine and are shown in the instructions, M5, M8 etc. ..

If the E1 error occurs after the belt starts to move for several seconds, the error code means that the system is not picking up the speed of the motor. This pickup comes from a magnet mounted on the front roller pulley and a speed sensor, or a problem with the magnet.Feb 29, 2016

E1 Error Codes - The Treadmill Engineer

treadmill-engineer.com http://www.treadmill-engineer.com > 2016/02 > e1-error...

Reebok ZR9 treadmill has E01 error on console since ...

JustAnswer https://www.justanswer.co.uk > electronics > ca4k2-ree... Reebok ZR9 treadmill has E01 error on console since moving · 1. Turn the machine off at the mains socket for at least 30 seconds · 2. Turn the machine on at the ...

• I have a Rebok ZR8 treadmill that displays an E01 error

  https://www.justanswer.co.uk > fitness-equipment > dwrp... It is the internal sensor tr the mainboard that has faulted. I am really sorry about this and you are going to have to return the unit to have these tested and ...

..

Hi Chris,Hope so you're doing well, fact that it runs briefly and then flips the fuse suggests a potential overload or short circuit problem. To troubleshoot the issue, start by checking the power source and ensuring that the circuit breaker or fuse can handle the treadmill's electrical load.Inspect the power cord for any signs of damage, fraying, or loose connections. Make sure it is securely plugged into the outlet. Additionally, examine the motor control board for any visible signs of damage, such as burnt components or loose wires.Testing the motor by disconnecting the power and manually rotating the treadmill belt can help identify any obstructions or issues with the motor or belt tension. If you are unable to identify or resolve the problem on your own then download now user guide, it is advisable to consult a qualified technician or contact the manufacturer's customer support for further assistance.Hope so this will help you!Regards,Bryce JuneCEO & Founder of https://trafficriderapp.com/

Just so you know, we aren't Rebook we are Fixya and just have a Reebok category for filing questions. Videos showing how they work.

Question edited for clarity. Question moved from Cellphones category. Limited help here, but there is a link to Reebok https://www.google.com/search?q=Reebok+gt40s+touch+screen+keeps+freezing ..

Question edited for clarity. Batteries 4 x 1.5V - size C Manuals https://www.google.com/search?q=reebok+rem-11200+power+bike ..

It sounds like there may be an issue with the incline motor or the lifting mechanism. Here are a few troubleshooting steps you can take:

1. Check for any visible damage or obstructions in the incline mechanism. Make sure that there is nothing blocking the movement of the incline motor or lifting mechanism.
2. Check the wiring and connections for the incline motor. Make sure that all wires are connected securely and that there are no loose or damaged wires.
3. Test the voltage going to the incline motor. Use a multimeter to check that the motor is receiving the correct voltage.
4. Try to manually adjust the incline. This will help you determine if the issue is with the motor or the lifting mechanism. To do this, unplug the treadmill and remove the motor cover. Locate the incline motor and manually turn the screw with an Allen wrench to raise or lower the incline. If the incline moves smoothly and easily, the issue is likely with the motor. If the incline is difficult to move or doesn't move at all, the issue is likely with the lifting mechanism.

If you're not comfortable performing these steps, it may be best to contact a professional to diagnose and repair the issue.

1. Check the belt: Make sure the belt is properly aligned and tensioned, as a misaligned or loose belt could cause the incline to get stuck.
2. Check the incline motor: If the incline motor is not functioning properly, it could be preventing the incline from moving. You may need to have the motor inspected or replaced.
3. Check the incline sensors: If the incline sensors are not functioning properly, they could be preventing the incline from moving. You may need to have the sensors inspected or replaced.
4. Check the control board: If the control board is not functioning properly, it could be preventing the incline from moving. You may need to have the control board inspected or replaced.

If these steps do no

It sounds like you're experiencing an E2 error on your Reebok GT40s treadmill. This error is indicative of a problem with the speed sensor, which may need to be replaced. Additionally, check your cables and connections to make sure they are all securely plugged in