20 Most Recent
Life Fitness 9100 Next Generation Remanufactured Treadmill - Page 2 Questions & Answers
I want to know what is a control processor and main processor for lifefitness treadmill 9100 and where it is located at. thanks
1_ CPU is SYSCON, is the unit control electronic,that sen all electronical signal to the electronic of equipment.2) tight every wires connector very well and clean it3) Run the software calibration for diagnose, troubleshooting , fix it4) However you must calibrate the REED swith, see the diagram, clean it, and tigh the wires connector very well, exchange the batteries by new ones and clean the contacts cleaner 5) tight the ribbon cables from keypads switch +tight the display board connector vs lower board and proof again.God bless you
My Life Fitness Display is completely dead, worked
Adjust for 1/8" and clean the sensor switch. Remember the main boar controller motor control the function for the display board(by power supply, electronic signals like the sensor reed, etc) Tight the flexible cable or ribbon cable and plug with carefully and paciencie, Disconnect the power cord
I have a Life Fitness 9100, and the display is
If the console takes
batteries, replace them. If this does not work or your console does not require
batteries, check the reed switch or optic sensor. Reed Switch:
Unplug the treadmill and remove the motor hood cover. The reed switch is mounted
on the frame next to the front roller pulley. There is a magnet glued into the
front roller pulley. When adjusting the reed switch, make sure it is pointing
directly at the magnet. Move the tip of the reed switch within 1/8" of the
magnet. Also, check to see that the wire is not damaged, and is connected to
the console.
Optic Sensor: Unplug the treadmill and remove the motor hood
cover. The optic disk and sensor are located either at the end of the motor or
the right hand side of the front roller. The optic disk spins between two
sensors on the optic switch. The disk must spin freely without touching either
sensor. The sensors can be moved by loosening the adjustment bolt holding the
switch to its bracket. The switch can then be slid. Center the disk. Adjust and clean very softly.
Describe your 9100 Next Generation
Dear Sir:
I will help you inmediately.
1) Display does not illuminate
when machine is powered
on.
Insufficient power source.
Plug treadmill into a dedicated amp circuit.
2) Loose 10 pin connection at
display console or wax/lift
control board.
Check all electrical connections for proper
attachment.
3)Damaged main harness wire
connection.
4)Replace wire harness.
Faulty display console or Wax/
Lift Board.
Verify if 8VDC is present at P1 pin, 3-4 and
12VDC at P1 pin 9.
a)If yes, replace Display Console.
b) If no, replace Wax/Lift Board. See How To...
Replace Wax/Lift PCB.
Use VOM digital (Voltimeter)
Hoping that you can resolve, if you need some extra help, please reach me.
blessing.
E.CUADRA
MANAGUA, NICARAGUA. C.A.
Client run on treadmill then
hi,
There are two possibilities for this problem
1. Check the speed sensor on near the motor pulley. Remove the sensor and clean it and re-fix it. then make a try. if problem remains then
2. The motor speed controller is faulty. There is an IGBT for controlling the motor speed. If it get shorted the motor will run it its high speed.
Be sure before opening the treadmill remove the power.
ok
I have a Lifefitness Treadmill model TR 9100,
Ive just had lifefitness out to diagnose the same problem, its the Console PCB £413.74 all in from them to fit yourself
Cant do anything else, save yourself the callout I was charged
Good luck
Adrian Webb
07780 993877
My lifefitness treadmill gives a static shocks...
hi you have a wire touching the body of the treadmill somewhere, but an easy fix is to go to any car parts shop and buy an antistatic strip. just attach that to the body of the treadmill making sure it is touching the ground, this will def fix your problem. i had the same with mine i spent ages looking for the wire etc but just waisted alot of time. the strip has worked very well.and cheap to buy under £5.00.
How i can change the laguage
keep pressed the key "pause" for a few seconds then search with the arrows until you reach "manager configuration" then change the lenguage y go!
Just got a used Life
this problem is due to a false in the terminals that connect with the microswitch, you must remove the screen and back-side only remove the screws and tighten the terminal
could also apply contact cleaner
Err 1 on fitness club threadmill
You will need to check the speed sensor for proper alignment and function. it should be located near the front roller or mounted on the motor. It should be within a credit cards width of the magnet or toothed wheel. If properly adjusted check with an ammeter to see if it is opening and closing by manually spinning the front roller or motor flywheel. If it isn't replace the sensor. If it is functioning make sure you are getting 5vdc to it across the wires. If you are not replace the upper control board(console). If you are getting the proper voltage then replace the lower control board(motor controller).
My Life Fitness 9100hr will run a few (under 10)
Hi,
This can be due to the friction setback between the deck and belt. The associated problems may cover tripping of circuit after working for a certain time period, or the treadmill automatically getting shut off, Reason being a loose end wire or faulty control panel.
Apply the lubricant under walking belt and adjust the belt tension.
Clean the speed sensor wheel with compressed air or a q-tip.
Sometimes dirt or dust obstruct the working of the treadmill, Visit this
Link for cleaning it.
Good Luck and have a nice day.
I have a life fitness treadmill and put new wax in
you will need to go into service menu by pressing and holding the pause button then pressing the clear button twice , continue holding the pause until the service menu appears. then use the arrow up and select maintenance press enter then either use arrow up or down scroll and say refill waxer system or replacing wax bag press enter, this will reset upper console. Upon completion of this the go back into the diagnostic menu select system test press enter scroll up or down to waxer manual mode hit quick start and that will fire up the wax pump and your done
Refilled with wax how to reset display
you have to enter maintenance mode, press (CLEAR) and then press the key (PAUSE) there will appear a message that is doing a checkup, then using the keys you move up to find "Maintenance" and press enter Ahi provided with keys look for the option "WAX REFILL" press "ENTER" and ready and be 100% if you have any additional questions here's my e
[email protected]
Not finding what you are looking for?