20 Most Recent Electrolux EW1209i Front Load Washer / Dryer - Page 8 Questions & Answers

first try reversing the hoses to see if that remidies it.

hello... it may help... error descr. cause action reset E43 Power triac on door interlock faulty Door safety interlock faulty; Wiring faulty; Circuit board faulty. Safety drain, door released Selector on "0"

find reset function bottons find youtube video how to reset your brand model or similar model and follow instructions on your owners manual

Can you turn off your overdrive? When towing most vehicles have an overdrive off mode. You can’t tow in 5th or 6th gear and may confuse computer and put car in protection loop mode.

I don't think you have all the correct error code. should be an "F" number before the "E" number. does make a difference. I want to give you the correct info.

If you remove the drain hose, and lay it down low as possable, it will drain the water out by gravity, this might help you out.

E21 is error for water not draining fast enough.

You may need to remove the front panel like on my Frigidare washer. Removing the retaining spring ring holding the seal may be tricky.
I learned from watching a repairman do it.

My filter got clogged because the drum impellers tend to break a piece and let change and stuff go to the filter.

Make sure water is on with cold connected to cold and hot. Make sure screens in hoses and valve are not clogged with debris

The tachometer or tacho-generator has the function of controlling the electric motor and the speed of the motor (rpm). So, could be electric motor blocked for some reason, worn out carbon brushes, faulty tachometer, wiring and finally electronic. After 5 years working of washing machine, by my experience the most common reason is worn out the brushes of electric motor. Dado

most likely worn out brushes on the motor or faulty motor

Firs of all check out error code number, then check out what it's mean in service manual booklet. Can be simple problem- drain are dirty, clean up.

Hello, I think that your drain pump is blocked of is faulty. You will need to drain the water from the machine, remove the drain hose from the drain outtlet on the wall. or sink unit. Once you have done this check that the pump filter ( if fitted) that it has not clogged with fluff or other debris, If that is not clogged, you will need to look under the machine and check the hoses from the drum to the pump for items like flimsy underwear, socks, or other small items, these can slow the water flow, stop it, or stop the impellor on the water pump. If that is not blocked. check that the drain hose to the domestic outlet is not blocked, as sometimes if you live in a hard water area, it can block with calcium deposits. I hope this helps?

10E: Water level is above parameter set (10 scale units) after water discharge

If you can get to the drain hose and hold it low down, the water should come out allowing you to get to the clothes. Be careful where the water goes though.

Disconnect power supply. Remove top panel. Now is door lock accessible. Open door, remove door gasket from housing (not from tub), remove two screws and replace door lock. Dado

The EH0 error indicates a problem with the incoming voltage or the power supply or wiring inside the dryer. If there has been a problem with the electricity coming into your home (brown out or similar), the error will resolve when the power company fixes the issue. Otherwise the control board is not receiving the expected power from the power supply. First unplug the dryer or shut off the power at the circuit breaker. Unplugging the dryer for at least 30 seconds will reset the error message. If you can, plug another appliance into the outlet and check if that works. If there is a wiring fault, get an electrician to check the outlet and wiring. If the problem is inside the dryer, the power supply, the control board and the wiring to the control board will need to be checked. There could be a loose wire, a broken wire or a spot where the insulation has been damaged and two wires are touching. Check all of the wiring harnesses where groups of wires plug into the control board. Replace or fix any damaged parts or wires. The parts diagrams are available here: https://www.ransomspares.co.uk/parts/brands/electrolux/tumble-dryers/edc2086glw%20(91609724100)/ . If the dryer is under warranty, contact Electrolux to have the unit serviced. I hope this helps. Cindy Wells

possibly could have motor bearings going out

5.5 Opening The Door (from user manual) While a program or the 'Delay Start' is operating, the appliance door is locked and the display shows the indicator 'key symbol '. First set the machine to PAUSE by pressing the "Start/Pause" touchpad. Wait until the door lock indicator 'the key symbol ' goes off, then the door can be opened. If the door lock indicator 'the key symbol ' does not disappear, this means that the machine is already heating and the water level is above the bottom edge of the door or the drum is turning. In this case the door CAN NOT be opened. If you can not open the door but you need to open it you have to switch the machine off by turn the program selector knob to the position " 0 " to deactivate the appliance. After about 5 minutes the door can be opened. CAUTION ! Pay attention to the water level and water temperature. Dado

1) It could be that the washing machine drum has collected greasy residue from previous loads. Try cleaning the drum by running an empty cycle with a cupful of white vinegar. 2) Or could be the bearings. When bearings are on the way out they leave streaky dark marks on the clothes.