Top 10 Electrolux EW1000i Front Load Washer Questions & Answers

Electrolux EW1000i Front Load Washer Logo

Question

  • 12,533 People Helped

Electrolux EWF1074 with Error EH0. After 2 seconds

Electrolux EWF1074 with Error EH0. After 2 seconds of turning on the start and pause button blinks in red. Anyone know what EH0 means? I called them and even they were unsure. They charged me 95$ just for coming in to tell me they dont know anything... So sick of scams

Posted by on

Answer

  • Most Helpful of 3 Answers

In case of error in the mains, or like what happend today at my house, the power lines went partially down, providing too low voltage, EH0 or EH1 will occour. If you also notice that the lightning indoor is somewhat dimmed during this error, the voltage is too low.

Posted on Jan 20, 2015

Question

  • 6,571 People Helped

Electrolux EWF 1074 - How do I turn off the annoying beeps at the end of every wash

I need to turn off the beeps at the end of every wash PLEASE

Posted by on

Answer

  • Most Helpful of 2 Answers

I have touchscreen! Doesnt work. Any suggestions? Hate having to get up middle of night to turn off this )%(/₪/#&/₪(" beep!

Posted on Jan 14, 2016

Question

  • 4,855 People Helped

error codes for Electrolux front load washer EWF 1087

E40 is the code showing

Posted by on

Answer

  • Most Helpful of 3 Answers

E40 error is door interlock faulty, could be the lock or it could be the pcb u have to test them.

Posted on Jun 25, 2010

Question

  • 4,821 People Helped

E10 & E20 problem

i also have an electrolux washer that flashes E10 and also E20 when it is half way through a cycle, now for some reason it isnt draining properly?

Posted by on

Answer

  • Most Helpful of 1 Answers

e10 problems refer to water supply..so check the tap is on, the inlet hose is not kinkrd, and the filter in the inlet hose is not blocked.  e20 refers towater drainage,  so check the drain hose isn't kinked and the drain pump isn't clogged

Posted on Aug 19, 2009

Question

  • 4,649 People Helped

Have a erro code E21 What is it

Have a erro code E21 What is it

Posted by on

Answer

  • Most Helpful of 4 Answers

The E21 error code means the water in the washer is not pumping out fast enough. The solution is to check the washer installation. Make sure the drain hose is not kinked. Make sure the drain pump has 120 volts in the drain cycle. If it reads zero the control board will need to be replaced. If not, then it's the pump.

Posted on Nov 05, 2009

Question

  • 4,540 People Helped

Zanussi Electrolux ZWF 1430 W (E20 error)

Hi I have a Zanussi Electrolux ZWF 1430 W and it's coming up with an E20 error code. The machine starts off OK but after about 25 minutes the Error Code E20 starts flashing in display and the machine stops with all the water still inside. I tried pausing the machine and skiping on to the next cycle and at first the machine strats spining again but after a few minutes the machine just stops and no error messages come up. I have misplaced the manual so can't look up what the error code means and shall be grateful if you could help me rectify the problem or shed some more light on it. Many thanks Hello, I have a 'Electrolux' front loader washing washine it keeps coming up with the error 'E20' it will wash for less than a minute but its like when it comes to the spinning cycle it stops then this error messages comes up. I have lost my instruction manual for it so I cannot look this up for myself, can you help me? Its also the 6.5kg and also has on the draw that you pull out to put your washing power in there is writting that says 'ECO VALVE' unsure what this is. Regards Melinda

Posted by on

Answer

  • Most Helpful of 5 Answers

I'm fairly sure that this is a warning that the filter is blocked. There is a filter in the bottom right hand corner of the machine.

Now, as stated by the other user here, your problem is that you have a machine full of water and if you remove the filter, you are going to get a very wet floor. The trick here is:

Turn the power off at the mains and remove the plug from the wall. Wait ten minutes. This SHOULD power off the safety feature that allows you to open the front load door.

Presuming it does, pull the machine out if it is under a work surface and taking great care because of the weight, tip tha machine backwards until the water level is below the door (Having a chair or a box to rest the back of the machine on is a good plan here, so you don't tip it beyond about 45% and have it fall on ots back.

If the door will open, then you can now rescue any clothes and bale out the water with a cup. Once you gave got to all the water you can (Memember there is still more waqter out of sight and in the pipe going to the filter!) You can now tip the machine back a little further until the water is clear of the filter in the botton right of the machine.

NOW, you can take the filter out, remove the fliff, couns, old sock and other debris clogging it and screw it back in place. TIp the machine back on to its feet and put it back.

Now, make a note in your diary to check the filter ever 6-8 weeks or so. Once you have done a few check and cleans, you will figure out how oftem you need to clean the filter, which depends on what you wash and how much you wash it.

Posted on Feb 15, 2009

Question

  • 4,135 People Helped

Electrolux EWF 1074 get a lock icon

Electrolux EWF 1074 get a ''lock'' icon on the display, but the door does open and close, just the machine doesn't work. The solution holding the Extra rinse and delay doesn't work for mine. Asking for another solution ?

Posted by on

Answer

  • Most Helpful of 1 Answers

you need to hold the option and extra rinse buttons simultaneously for 6 seconds...you will see the padlock symbol go and then use your machine as usual

Posted on Aug 19, 2009

Question

  • 3,888 People Helped

How to run tHe self cleaning cycle on electrolux

I need to know how to manually get to the option on the screen that allows you to run the self cleaning bleach cycle on electrolux laundry washing machine

Posted by on

Question

  • 3,876 People Helped

Electrolux 1087 E90

When the washing machine is turned on... it beeps and displays error message E90 it wont operate.

Posted by on

Answer

  • Most Helpful of 4 Answers

When the washing machine is turned on... it beeps and displays error message E90 it wont operate.

what can i do ?

Posted on Mar 08, 2008

Question

  • 3,446 People Helped

electrolux EWF 1282 start pause button is flashing wont start a load have reset it no error messages came up have also cleaned the drain filter the manual way underneath the machine still nothing any

thank you for any help

Posted by on

Answer

  • Most Helpful of 2 Answers

Hello terry_gwen - Based on the symptoms you are describing, you may either have a communication error from the main control board or the timer itself may not be operating correctly. I understand that the filter has been cleaned, however, if you noticed a humming noise, it could either be a clogged drainage hose, or it could possibly have another issue with the door lock assembly. I would personally contact a professional to accurately diagnose the washer to determine the root cause to reduce the risk of unnecessary parts.

Posted on Apr 16, 2013

440 questions posted

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Brad Brown

Level 3 Expert

18825 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

EW1000i Front Load Washer Electrolux

  • EW1000i Front Load Washer Electrolux

Most Popular Question

front load washing machine working but

  • Washing Machines
Loading...