20 Most Recent
Humminbird Matrix 12 Fishing System - Page 9 Questions & Answers
How to get the cover off of a mn star fuse box on a premier pontoon
To remove the cover of a MN Star fuse box on a Premier pontoon, you can follow these steps:
- Locate the MN Star fuse box on your Premier pontoon. It is usually located in the helm area or in a console.
- Identify the locking mechanism that holds the cover in place. It may be a latch or a screw that needs to be unscrewed.
- If it is a latch, press the latch and lift the cover. If it is a screw, use a screwdriver to unscrew it and then lift the cover.
- If the cover is still stuck, check for any additional screws or latches that may be holding it in place.
- Once the cover is removed, you should have access to the fuses and wiring inside the box.
- When putting the cover back on, make sure it is properly aligned and locked in place to ensure proper protection of the fuses and wiring.
If you are still having difficulty removing the cover or have any concerns, it may be helpful to consult the owner's manual or seek assistance from a professional.
2/23/2023 5:21:07 PM •
Boating
•
Answered
on Feb 23, 2023
My VTS stopped working on my 2007 Seadoo RXP. When I press the up button there is a long beep after a 2-3 second pause.I wired the VTS motor direct to the battery and found it works perfectly.
Based on your description, it's possible that there is an issue with the VTS switch or a relay. Here are some troubleshooting steps you can try:
- Check the VTS switch: Use a multimeter to test the switch and make sure it's functioning properly. You can also try cleaning the switch contacts with electrical contact cleaner.
- Check the relays: There may be one or more relays in the VTS circuit that could be causing the issue. Use a multimeter to test each relay and make sure it's working correctly.
- Check the wiring: Inspect the wiring for any signs of damage or corrosion. Make sure all the connections are clean and tight.
- Check the fuse: There may be a fuse that protects the VTS circuit. Check the fuse and replace it if necessary.
If none of these steps resolve the issue, it may be necessary to take the watercraft to a professional mechanic for further diagnosis and repair.
2/23/2023 5:03:38 PM •
Boating
•
Answered
on Feb 23, 2023
Where do I add fluid for the tilt trim on evinrude 90hp 2006 motor
The tilt and trim fluid reservoir for a 2006 Evinrude 90hp motor is typically located on the side of the tilt and trim unit, near the bottom of the motor. It may be a small plastic or metal container with a screw cap or plug. To add fluid, first, ensure the motor is in the full tilt-up position and that the tilt and trim system is not in operation. Then, remove the screw cap or plug and add hydraulic fluid until it reaches the full mark on the dipstick or sight glass. Use the recommended fluid type specified in the owner's manual or on the reservoir cap. Finally, replace the screw cap or plug and wipe away any excess fluid. It's recommended to check the fluid level periodically and add more fluid as necessary.
2/23/2023 5:00:35 PM •
Boating
•
Answered
on Feb 23, 2023
Where is the 85 horse Evinrude get its oil?
The 85 horsepower Evinrude outboard engine has a separate oil tank for its 2-stroke oil. The oil tank is usually located in the engine compartment and is connected to the engine through hoses. The engine's oil injection system will automatically mix the oil with the gasoline as needed, so the operator does not have to manually mix the oil and gasoline. It is important to regularly check the oil tank level and refill it as needed to ensure proper engine performance and longevity.
2/23/2023 4:56:23 PM •
Boating
•
Answered
on Feb 23, 2023
Minn kota e drive
I may can help. First, sit down and sip on a cold one. (coke,beer,ice tea,ect). Please send me model of unit including all options. I will research unit & reply ASAP. Maybe just a bad connection internally.
12/24/2022 1:59:17 PM •
Boating
•
Answered
on Dec 24, 2022
What should I look for in a structural engineer in Hull?
If you need to hire a structural engineering specialist, you first and foremost want someone with genuine experience. You should keep an eye out for companies that have a long-standing history within the region. For example, companies like
GGP Consult offer access to the kind of structural engineer Hull developers should be looking for.
Primarily, you should be focusing on finding someone who has designed something similar to what you are looking for. Look through their portfolio and ensure they have something in their professional history that matches up with what you will be building.
While most structural engineers can be quite versatile, it pays to know that your selected expert has built something that matches your ideas beforehand. Focus on these areas when hiring a Hull structural engineer.
9/23/2022 10:31:49 AM •
Boating
•
Answered
on Sep 23, 2022
Not finding what you are looking for?