Frigidaire GLTF2940F Front Load Washer - Answered Questions & Fixed issues
GLTF2940FS2
Ok no timer switch on
Check with your appliance parts repair people in your area.
You should find no one will touch the electronic control panel. Usually, the time it takes and the cost for diagnostics will negate any profit for the business.
Same as why many cars must go back to the dealer for electronics. Most of your local repair people will just replace the board.
God bless your efforts.
7/7/2017 6:00:27 PM •
Frigidaire...
•
Answered
on Jul 07, 2017
•
129 views
Gltf2940fs
washer stopped working, displayed E5E error when prompted for code. I opened up the back of the machine and noticed that a connector was not connected to the control board, i removed the control board to get a better view of where it belonged, and slid the connector over the control board, closed up the machine and it's back in business.
7/23/2015 2:33:44 AM •
Frigidaire...
•
Answered
on Jul 23, 2015
•
412 views
Remove paneling to work on the machine
Good Afternoon Friend,
I understand you want to remove the paneling on your Frigidaire washer, model# GLTF2940F, to work on your machine. Typically, this is not a do it yourself action, as there are no step by step instructions on how to remove the paneling. I suggest either contacting the manufacturer or your local authorized technician for further assistance. Hope this is helpful.
-Best Regards-
WP
7/1/2014 5:05:43 PM •
Frigidaire...
•
Answered
on Jul 01, 2014
•
73 views
Code e62 on frigidaire gallery series model GLTF2940FS2
Good Morning Friend,
I understand you are receiving an E62 code on your Frigidaire Gallery washer, model# GLTF2940FS2. The E62 code means that there is a communication problem between the different control boards in your appliance. I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Restore power and start any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully. Hope this is helpful.
-Best Regards-
WP
6/30/2014 2:52:35 PM •
Frigidaire...
•
Answered
on Jun 30, 2014
•
932 views
Washing but not spining out clothes
Take the power plug off the wall. Be prepared for a lot of water before attempting the following. It doesn't spin because the unit is not draining water. It will not spin with water in it - must drain first. Check drain hose for kink,check exit pipe for blockage, then check pump. Could be your "coin trap assembly" is blocked, therefore not allowing all the water to pump out. Remove the front access panel, and remove the clamp that connects this trap assembly to the pump and clean it out. If helped pl say so, thanks.
4/2/2013 12:00:41 PM •
Frigidaire...
•
Answered
on Apr 02, 2013
•
168 views
E41 ERROR
E41 Control board thinks the door switch is open.In the J2 plug on the control, measure voltage from the black wire to ground with power on.0 volts. Check the door strike. If good, replace the door switch assembly.120 volts. Replace the control board.
5/12/2012 12:12:38 PM •
Frigidaire...
•
Answered
on May 12, 2012
•
678 views
Will not drain
Check your drain hose to make sure its not kinked or clogged. If OK try the other washing selections If same on all wash cycles. The pump is not performing correctly
2/19/2012 11:10:22 AM •
Frigidaire...
•
Answered
on Feb 19, 2012
•
85 views
Won't drain. Blinking pause. Won't
Hi.
You need to check the
drain filter, which is directly connected to the pump. That is the place where you usually find blockage. The filter or coin trap is located inside the drum. See the schematic below:
If that is not enough, then the drain pump access is located in the front side of the machine, hidden behind the trim at the base. The kick panel is held to the washer's frame by screws:
After removing the panel you will Be able to access the pump. Have a container ready to collect water that will come out through the hose.
DISCONNECT POWER before starting the job.
Here parts diagrams: GLTF2940FS1 - parts catalogHere a page about drain/spin problem.
If you need parts see this tip explaining how to find parts and diagrams for most appliances: Where do I find parts and diagrams for my appliance?
Regards.
Ginko
9/10/2011 11:05:18 AM •
Frigidaire...
•
Answered
on Sep 10, 2011
•
716 views
Washer starts at 44 minutes
Turn the machine off then unplug it for at least 5 minutes then plug it it back. Turn on the washer then
press any button and wait for 5 seconds. Press and hold the START/PAUSE and CANCEL buttons simultaneously. As long as the buttons are held, the most recent
failure code will appear on the display as an "E" followed by two
numbers, a number and a letter or two letters. The control will beep and
the Door Lock, Wash, Rinse, and Final Spin indicator lights will flash. Post back the error code, if there's any, for further troubleshooting and repair
advice. Indicate the exact model number of the machine if the procedure prescribed here is not applicable.
You
don't have to accept or reject this post in order to add comment or
information. But accepting the solution
should you find it helpful and/or informative will not stop you from
posting comments or additional information. You can still communicate with the expert should you need further advice regarding the issue stated herein.
7/27/2011 9:56:25 PM •
Frigidaire...
•
Answered
on Jul 27, 2011
•
203 views
When I start my washer,
I have the same washer the code for that is control board thinks the door switch is open..to repair it said to check pressure switch....something about these washers front door problems.....
6/20/2011 6:20:52 PM •
Frigidaire...
•
Answered
on Jun 20, 2011
•
130 views
Washed some rugs with rubber
Clean the filter in the accordion hose just before the pump. It is clogged and or materials have reached the pump. You will get an error E 21
PanamaGuy
5/22/2011 6:13:05 PM •
Frigidaire...
•
Answered
on May 22, 2011
•
186 views
The tub does not turn in the rinse/spin cycle but
Hello Jwwood,
Your Frigidaire GLTF2940F washer is not moving when it is washing clothes. This is because the belt is broke you can locate the belt on RepairClinic.com. Before you order the belt you need to findout the length as there are many different lengths and styles. In order to get to the belt you need to remove the back of the unit. If it is broke as I beleive measure and post back to this thread or go to the following link find the proper size and order. LInk -
http://www.repairclinic.com/Frigidaire-Washing-Machine-Belt-Parts
Thank you for choosing FixYa.com
3/21/2011 1:44:57 AM •
Frigidaire...
•
Answered
on Mar 21, 2011
•
180 views
Its tearing my clothes
Check the drum for sharp edges or something metal caught in a seam or crack..run your hands thoroughly over the entire insides.
2/23/2011 5:30:50 PM •
Frigidaire...
•
Answered
on Feb 23, 2011
•
121 views
My washer not sping out code error is e 21
Hi Error code e20/e21 means a clogged drain pump. This might have happened due to small clips, pins, coins, etc being stuck in the pump. Please note that error e21 can also occur when the drain pump is not pumping fast enough or when the pump fails. To fix the issue you'll need to check the drain pump.Remove the 2 screws from the bottom of the front access panel, it will come off. Now check for the pump on the right side and remove hoses from it. Remove pump from machine then remove whatever is there in the pump. Hope this helps... Please post back for any further assistance.
9/29/2013 9:28:52 PM •
Frigidaire...
•
Answered
on Sep 29, 2013
•
746 views
Washed rubber backed rugs in washer, backing
Take lower kick plate of machine pump is behind it//// remove rubber tub to pump hose some frigidaires have a little coin trap in there some don;t clean hose out out back togeather //If I helped please vote if you need more help please ask Good luck
2/4/2011 9:21:41 PM •
Frigidaire...
•
Answered
on Feb 04, 2011
•
350 views
Frigidaire front load washer GLTF2940FS barely
Yes, there is a filter on your machine. If you look in from the back, on the bottom of the tub is a hose coming off. Remove the hose from the tub section and inside of it you will find the filter.
Have a great New Year!
5/22/2011 6:04:20 PM •
Frigidaire...
•
Answered
on May 22, 2011
•
754 views
Not finding what you are looking for?