Top 20
Nextar M3 Car GPS Receiver Questions & Answers
1 Answer
Need map up date can
To update the existing map for you Nextar product, please contact Nextar to find out if any new map information has become available. Nextar products are usually pre-loaded with USA/Canada maps, depending on the model. If you need updates
Contact Support
[email protected] in USA or GB for new maps
and quote your model number
Nextar M3 Car...
|
503 views | 2 helpful votes
1 Answer
Bought a m3 nextar gps
First you have to Set your GPS On the right Satellite Like Mangella GPS signal ...Look in the Manual or Downlod It From The Net Like Exemple...... (download Nextar M3 GPS Manual Utility, Then chose the one will Guide your to the right position USA Or CANADA Position accroding your Street Name, Good Luck.....
Nextar M3 Car...
|
151 views | 0 helpful votes
1 Answer
I have the m3 but it says the software is the 5.5
Hi,
Sync the unit to your computer and copy files to your media folder on the SD Card. Better still, remove the card, plug it into your computer's card reader, then copy direct to the card. You may need a lager card. Some of these units will take up to 4GB cards.
Thanks, Bill
Nextar M3 Car...
|
96 views | 0 helpful votes
1 Answer
Nextar GPS Never acquires GPS Signal
The only thing you can try is the external antenna for this unit.
You could be in an area that has poor signal.
If it where me, I would go to a place that I could return a unit,
I only use garmin, there hand-held unit's are the top rated for
the frequency of getting satellites.
So say you have a walmart, see if you can return a unit, buy a garmin
and see if it get better reception, and if it doesn't then its not the unit.
If it does,sell you old one on ebay.
Nextar M3 Car...
|
356 views | 2 helpful votes
1 Answer
Cannot find map data files
Hello,
Thanks for using FixYa.
If you GPS receiver is unable to pull up some map data, you probably need to download them into your device. You can get map files from the GPS manufacturer. Map files from other manufacturer might work as long as they use the same data file type.
I hope this helps. Happy new year and happy new decade.
- HotRatchet
Nextar M3 Car...
|
74 views | 0 helpful votes
1 Answer
Need to upgrade the maps on my nextar x3-03
To update the existing map for you Nextar product, please
contact Nextar to find out if any new map information has become
available. Nextar products are usually pre-loaded with USA/Canada maps,
depending on the model. If you need updates
Contact Support
[email protected] in USA or GB for new maps
and quote your model number
Nextar M3 Car...
|
1,905 views | 0 helpful votes
1 Answer
I have error 6020
this is a chip board failure error.the chip needs to checked and some minor repairs needed on the board.most cases the dry solder on the board will solve the issue. its a rare problem.
This will
help. Thanks, please keep updated. please do rate the solution positively .thank
you for using fixya
Nextar M3 Car...
|
29 views | 0 helpful votes
1 Answer
I have a new computer with Windows Vista and when
the solution might be as simple as going to Nextar's website and downloading a new driver that's compatible with vista. A problem I had when I purchased a new computer is that it had a 64bit vista operating system which rejected too many programs and drivers were not available. My solution was to install the 32 bit vista and it solved many, not all, of my problems. Good luck.
Nextar M3 Car...
|
251 views | 0 helpful votes
1 Answer
Nextar GPS will not get past loading stage
Nextar will not assist in helping "fix" anything. Their solution is for you to send in the unit and they pitch it, send you one off the assembly line. I was able to get this unit working again in just GPS mode (what it was intended for), so using this workaround, you will lose the ability to use it as a tiny digital photo frame, MP3 player, etc.
I take no responsibility if you try this and "brick" your unit (render it unusable except as a $100 paper weight). BACK UP!!
1) Download and install ActiveSync from the Micro$oft website.
2) Connect the M3-04 unit to your computer
3) Turn it on
4) Red bar should fill and the M3-04 will "hang" in that screen, BUT viola it still connects to ActiveSync
5) Using Explorer from ActiveSync, navigate to ResidentFlash
6) Copy autorun.inf to your PC Desktop, make backup by renaming it to autorun.bak
7) Open autorun.bak with Notepad
8) Change the line to read without the quotes: "\ResidentFlash\Netropa Intellinav\IntelliNav.exe"
9) Save As to your desktop autorun.inf
10) Copy back to your ResidentFlash directory on the M3-04
11) Disconnect from PC and hit the reset button on back....BOOYA! Your GPS is functioning again.
Nextar M3 Car...
|
948 views | 0 helpful votes
Not finding what you are looking for?
