Top 20 Fisher and Paykel WL26CW1 Top Load Washer Questions & Answers

if it was left switch on at the wall when the power came on again it probably blew the computer board due a current surge

whaat model do you have? there a few slightly different things you can do. most common is hold start, press power. then power off. and back on.

Hi, With the board replacement, did you program this board for this unit? If not, thats the problem you have now. Good Luck I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Read page 4 http://www.rakerappliancerepair.com/NephewClub/Diagnostics/Washers/Fisher_Paykel/F-P%20-%20Bulletins%20-%204-08.pdf

All replaced electronic boards need resizing. Going by your post your have an AquaSmart machine Here are some details to resize an AquaSmart machine

Fault 9 LAH HIGH CURRENT FAULT The low ambient heater is drawing more current than expected. Either the heater or wiring is faulty. Primary Action - Check the wring and connections at both heater and power module. Secondary Action - Check heater resistance. If not within limits replace heater.

Hi, Call the factory 888-936-7872, they can help you over the phone. 24/7, they are always willing to help. You may need to re-program this board. Good Luck I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

this is usuallt the R.P.S which is locked on the motor take off plastic cover by un doing centre nut loosen stator pull forward a little and remove stator

The most common problem with AquaSmart is the pump not the water valves The pump has gone bad and blown some parts in the motor controller board and the fuse to the water valves. Some AquaSmart machines display the wrong Error code (49) witch is not the correct code for this problem. Pump and motor controller board need replacing. Maybe cheaper to buy a good secondhand machine.

clean the senser and trie boling water

Might need to clean the sensor. Run through a rince cycle without clothes in it

240. (11110000) Hall Out Of Order. RPS Fault Same as previous Hall Error faults See fault code130 for directions. 130. (10000010) Single Rotor Position Sensor Error The Motor Control Module has found an error in the pattern received from the Rotor Position Sensor. Likely causes of this fault are a bad connection on the harness between the Rotor Position Sensor and the Motor Control Module, or a faulty Rotor Position Sensor. Primary Source: Wiring. Action: Check for corrosion on the RAST connector of the Rotor Position Sensor and the Motor Control Module connector. Secondary Source: Rotor Position Sensor. Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if faulty. Tertiary Source: Motor Control Module. Action: Replace Motor Control Module. Quaternary Source: Rotor Action: Ensure the correct rotor for this phase of machine has been fitted

Unplug it overnight! If you need further help, reach me via phone at https://www.6ya.com/expert/steven_b77d19396bfe2249

If the plug is fused then the fuse should blow before an appliance catches fire. If you go here they have a great customer service base and can recommend an authorised agent to look at and repair your machine if needed. If you want a manual they can also supply you with one just to make you more confident about the operation of your machine.http://www.fisherpaykel.com/us/laundry/?productUid=49343ABD-C773-932B-26D02C8672FC7E2B

no as it is soldered onto the main board

That is error code 130 130. (10000010) Phase 1 to 6 - Single Rotor Position Sensor Error The Motor Control Module has found an error in the pattern received from the Rotor Position Sensor. Likely causes of this fault are a bad connection on the harness between the Rotor Position Sensor and the Motor Control Module, or a faulty Rotor Position Sensor. Primary Source: Wiring. Action: 1. Check for corrosion on the edge connector of the Rotor Position Sensor and the Motor Control Module connector. 2. Check the contacts on the rotor positional sensor end of the hall harness to see if any have been damaged. (Each set of contacts in the socket has two wipers. If the distance between these wipers varies between different contacts, replace the rotor positional sensor harness.) Secondary Source: Rotor Position Sensor. Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if faulty. Tertiary Source: Motor Control Module. Action: Replace Motor Control Module.

This is the one for the led type

Did mean neck ring strap 3.

check the cylinder

Thanks for choosing FixYa and welcome to the site. Are you sure it is 24? Below is a link to the manual. The error codes are about 1/3 of the way down.


http://www.scribd.com/doc/48997386/Fisher-and-Paykel-SmartDrive-Service-manual-053-MW053-u-2010-05-31-170211-GWL-11US-FandP-service-manual