20 Most Recent Fisher and Paykel WL26CW1 Top Load Washer Questions & Answers

0helpful
1answer

Fisher and paykel washing machine fault code 9 how to fix

All replaced electronic boards need resizing. Going by your post your have an AquaSmart machine Here are some details to resize an AquaSmart machine 24903416-ei0rt0v231vo43kgyqwiblfx-4-1.jpg
5/2/2018 4:04:47 AM • Fisher and... • Answered on May 02, 2018
0helpful
1answer

Is it possible to change a fuse in an F&P aquasmart washing machine without a soldering iron?

no as it is soldered onto the main board
4/21/2018 1:17:15 AM • Fisher and... • Answered on Apr 21, 2018
0helpful
1answer

Where is the master overload breaker on a Fisher Paykel WL26CW1 washing machine?

if it was left switch on at the wall when the power came on again it probably blew the computer board due a current surge
3/2/2018 9:53:39 PM • Fisher and... • Answered on Mar 02, 2018
0helpful
1answer

Fisher and Paykel IW 712AU Top Load Washer Fault Code 130

this is usuallt the R.P.S which is locked on the motor take off plastic cover by un doing centre nut loosen stator pull forward a little and remove stator
10/26/2017 2:24:26 AM • Fisher and... • Answered on Oct 26, 2017
0helpful
1answer

Fault code 9 fisher and paykel

Hi, With the board replacement, did you program this board for this unit? If not, thats the problem you have now. Good Luck I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249
2/2/2016 12:19:10 AM • Fisher and... • Answered on Feb 02, 2016
0helpful
1answer

Fault 240 wl80t65cw1

240. (11110000) Hall Out Of Order. RPS Fault Same as previous Hall Error faults See fault code130 for directions. 130. (10000010) Single Rotor Position Sensor Error The Motor Control Module has found an error in the pattern received from the Rotor Position Sensor. Likely causes of this fault are a bad connection on the harness between the Rotor Position Sensor and the Motor Control Module, or a faulty Rotor Position Sensor. Primary Source: Wiring. Action: Check for corrosion on the RAST connector of the Rotor Position Sensor and the Motor Control Module connector. Secondary Source: Rotor Position Sensor. Action: Check the Rotor Position Sensor with an R.P.S. tester. Replace if faulty. Tertiary Source: Motor Control Module. Action: Replace Motor Control Module. Quaternary Source: Rotor Action: Ensure the correct rotor for this phase of machine has been fitted
9/14/2014 9:40:25 PM • Fisher and... • Answered on Sep 14, 2014
0helpful
2answers

Fault 9 flashing on wl26cw fisher and paykel washer

Fault 9 LAH HIGH CURRENT FAULT The low ambient heater is drawing more current than expected. Either the heater or wiring is faulty. Primary Action - Check the wring and connections at both heater and power module. Secondary Action - Check heater resistance. If not within limits replace heater.
8/15/2014 3:46:14 AM • Fisher and... • Answered on Aug 15, 2014
0helpful
2answers

Fault code 9 for fisher and paykel washer

whaat model do you have? there a few slightly different things you can do. most common is hold start, press power. then power off. and back on.
8/15/2014 3:23:05 AM • Fisher and... • Answered on Aug 15, 2014
0helpful
1answer

How to reset a washing machine

Hi, Call the factory 888-936-7872, they can help you over the phone. 24/7, they are always willing to help. You may need to re-program this board. Good Luck I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249
8/4/2014 12:54:45 PM • Fisher and... • Answered on Aug 04, 2014
0answers

Fault code 27

Be the first to answer 6/27/2014 3:46:04 AM • Fisher and... • Posted on Jun 27, 2014Be the first to answer
0helpful
1answer

Fisher & Paykel WL26CW1 - Error Code 49! can i swap the hot and cold valves to make it work and disconect the hot valve?? and love this site very informative, Thanx Guys..

The most common problem with AquaSmart is the pump not the water valves The pump has gone bad and blown some parts in the motor controller board and the fuse to the water valves. Some AquaSmart machines display the wrong Error code (49) witch is not the correct code for this problem. Pump and motor controller board need replacing. Maybe cheaper to buy a good secondhand machine.
5/20/2014 10:17:31 AM • Fisher and... • Answered on May 20, 2014
0helpful
1answer

Why does my wl26cw1 say too many suds

Might need to clean the sensor. Run through a rince cycle without clothes in it
4/26/2014 1:46:50 AM • Fisher and... • Answered on Apr 26, 2014
0helpful
1answer

Washer icons won't show up and washer sparks at plug when I plug it in.

If the plug is fused then the fuse should blow before an appliance catches fire. If you go here they have a great customer service base and can recommend an authorised agent to look at and repair your machine if needed. If you want a manual they can also supply you with one just to make you more confident about the operation of your machine.http://www.fisherpaykel.com/us/laundry/?productUid=49343ABD-C773-932B-26D02C8672FC7E2B
3/11/2014 1:14:07 PM • Fisher and... • Answered on Mar 11, 2014
0answers
0answers
0answers
Not finding what you are looking for?
Fisher and Paykel WL26CW1 Top Load Washer Logo

56 questions posted

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Fisher and Paykel Washing Machines

  • Fisher and Paykel Washing Machines

Most Popular Question

fisher amp paykel wl26cw1 error code

  • Washing Machines
Loading...