20 Most Recent Haier HDP18PA Stainless Steel Free-Standing Dishwasher - Page 5 Questions & Answers


Their is 2 screens towards the back right that are plugged up. . You can take out 2 screws out and clean them up. Or the fill level adjustment in the front left isn't working right. It also can be fixed with 2 screws and cleaned.

Haier... | Answered on Apr 21, 2014


Kink in the line or possible obstruction in the discharge, very bad to leave stagment water in your dishwasher you can get contaminents that way, I suggest from experience and to be safe to use extra hot water and bleach a tablespoon or so, and flush thru there, also check the hoses make sure they are not blocked and thewre is an air gap, and the height of the discharge is proper. After flushing get a box of baking soda, and some distilled vinegar and under neath your sink you will see the discharge or p trap, either place that in there thru the sink drain or put in the dishwasher with no dishes of course and allow the vinegar and baking soda enough to just reach the drain turn off unit and let the vinegar bomb do its thing, this also works for your laundry drain too, always good to flush them every now and again, if you start getting water backing up in your tub, you need a pump of your septic tank, or a thaw, or if on city water and sewer, you have blockage, hope this helps, good luck

Haier... | Answered on Nov 05, 2013


As a homeowner call a serviceman. Otherwise as a serviceman familiar with operational safety, remove the front kick plate cover at the bottom of the unit and then with a flashlight find exactly where the leak is coming from. The door seal or the drain pump? The intake hose or the drain hose? Determine if the unit is filling or draining or washing when the leaking starts. Then we can determine how to fix it.

Haier... | Answered on Oct 25, 2013


Why do you say this, I don't understand the problem. Are you telling about the 3 in 1 tablets?

Haier... | Answered on Sep 19, 2013


Hi,

The scum, film and white residueproblems have started since the reductionof phosphates in dishwasher detergents.

Here is a tip that will help you to solve the problem of films, residue, and scum in your dishwasher.

DishwasherResidue and Film on Dishes

heatman101

Haier... | Answered on Aug 08, 2013


It is possible that the machine does not start off the cycle because there are errors or back feedback from the inputs. For the program to start up the main program controller must initiate the INLET valve to open up and allow water to flow into. If this does not happen then the voltage at the inlet valve must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor .

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the drain valve/pump activated so as to drain off all the water .

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.espares.co.uk/advice/dishwashers/a/3

Haier... | Answered on Jan 27, 2013


id say pc board or the thermostat between the element

Haier... | Answered on Jan 18, 2013


After reading a few of the other Haier models troubles, I pulled the unit out and tip it at 45 degrees backwards for around minute. Water pored from the back of the unit, once cleaned water up reinstalled unit and all seems to be back in working order.

Haier... | Answered on Nov 28, 2012


see this causes and fix . God bless you
Float Switch

The float switch may be hung up and this can cause the dishwasher to be stuck in a cycle. Check the tutorial and the video for checking this part.

Timer / Control

If your dishwasher gets stuck in a cycle first try shutting off the breaker for at least 5 minutes if this does not correct the problem you will need to replace the timer / electronic control.
see the temperature sensor.for E4
God bless you

Haier... | Answered on Oct 03, 2012

Not finding what you are looking for?
Haier HDP18PA Stainless Steel Free-Standing Dishwasher Logo

64 questions posted

Ask a Question

Usually answered in minutes!

Top Haier Dishwashers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18564 Answers

Peter

Level 2 Expert

202 Answers

Are you a Haier Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Haier Dishwashers

  • Haier Dishwashers

Most Popular Question

hdw101ss not heat water

  • Dishwashers
Loading...