20 Most Recent
- Page 3 Questions & Answers
Robotoolz RT-7201 stopped working. Lazer
Try putting it in a freezer for at least 45 minutes. For some reason the diode seems to respond to the condensate, and it keeps working even after it thaws. This worked for two laser diodes on my 5 point Stanley Fat Max after trying everything else.
9/18/2011 2:57:11 AM •
on Sep 18, 2011
On my wireless weather station the last step has e d f I s not in that order just one letter each time I push what is it for
It is impossible to give you complete information without the Manufacturer name and the model number.
My guess is that you are pushing the mode button and skipping through 5 sets of settings. when you see the "e" push the up and down and you will probably see this sequence "e,c,m,p" if so, (or similar), that will set your time zone to Eastern, Central, Mountain, or Pacific.
The "d" is likely for the Daylight savings time, use the arrow when you see the "c" and if you see "d,s" those are for Daylight savings, and Standard.
I really am "shooting in the dark" without a make and model #.
How do you set barometer
I'm used to barometric pressure as related to altimeter setting in aircraft, but the principal is the same.
For an altimeter, If you know the elevation (above sea level) that you are at, and you set the altimeter to that altitude, the barometric pressure showing on the altimeter will be the current barometric pressure.
If you have a barometer without an altimeter, someone would have to provide you with the current setting. That would probably be your nearest weather station, airport, or your computer.
Here's a link to one.
Pressure and tendency refers to barometric pressure.
If you reply as a COMMENT to this post I will try to assist if possible.
Is there any way to change the battery on a Trumeter 5505E measuring whee
5505E MEASUREMETER BATTERY CHANGE (3V CR-2032)
REMOVE WHEEL AND SHAFT BY GENTLY PULLING AXLE OUT OF UNIT.
DRILL OUT 7 PLASTIC HEADS WITH 3/16 DRILL BIT. (ABOUT 1\8 DEPTH)
SPLIT TWO SIDES OF CASE AND REMOVE HANDLE.
SLIDE OUT CLEAR PLASTIC CONTROL UNIT. PUSH DOWN ON BUTTONS AS YOU REMOVE SO AS NOT TO DAMAGE THEM.
PUSH DOWN SLIGHTLY TOWARD THE CASE ON LOCK TABS WHILE GENTLY PULLING CASE APART. START ON ONE END AND WORK YOUR WAY TO OTHER END. KEEP GASKET INTACT. OPEN CASE.
THERE IS A "Y" SHAPED RETAINER HOLDING IN THE BATTERY. WITH NEEDLE NOSE PLIERS, CAREFULLY SLIGHTLY SQUEEZE THE BOTTOM OF THE "Y" AND PULL UP GENTLY. YOU CAN NOW REMOVE THE BATTERY AND INSTALL THE NEW ONE. PUSH RETAINER DOWN TO LOCK BACK IN.
MAKE SURE GASKET IS IN PLACE AND PUT CASE BACK TOGETHER, MAKING SURE WHEEL ADAPTER IS IN PROPER PLACE. TURN ON AND TEST CONTROL UNIT AND TURN WHEEL ADAPTER TO MAKE SURE UNIT IS WORKING PROPERLY.
SLIDE CONTROL UNIT BACK IN BEING CAREFUL OF THE BUTTONS. RE-ASSEMBLE HANDLE AND PUT THE TWO SIDES OF THE CASE TOGETHER. I USED THREE PIECES OF ELECTRICAL TAPE TO HOLD CASE TOGETHER. ONE ON THE TOP BETWEEN THE TWO HOLES, ONE ON THE BOTTOM JUST ABOVE THE DISPLAY, AND ONE IN THE MIDDLE.
PUT THE PLASTIC PIECE IN THE HOLE AND LINE UP. MAKE SURE BOTH O-RINGS ARE ON THE AXLE SHAFT. GENTLY INSERT AXLE ALL THE WAY IN WHILE ROTATING IF NECESSARY.
I WAS SO HAPPY I HAD IT ALL BACK TOGETHER AND WORKING, I HADN'T TAKEN ANY PICTURES AND I DIDN'T FEEL LIKE TAKING IT ALL APART AGAIN. MIGHT ADD PICTURES LATER IF NEEDED. I HAD BEEN LOOKING FOR YEARS ON HOW TO CHANGE THE BATTERY, AND I FINALLY MADE UP MY MIND THAT I WAS GOING TO DO IT.
Not finding what you are looking for?