20 Most Recent
Mitutoyo 0 150mm X .02mm Dial Caliper - Page 6 Questions & Answers
Large mitutoyo micrometers
I would recommend that you set each rod to zero using a set of jo-blocks to be perfectly accurate. I've been in the trade for 40 + years and this would be best for you. hope this helps you
10/17/2009 1:43:53 AM •
Mitutoyo...
•
Answered
on Oct 17, 2009
My mitutoyo O.D. mic measures .001 bigger than it
If you are certain that everything is clean and otherwise in good condition, adjust it to read correctly by rotating the graduated cylinder with a special spanner wrench typically supplied with the mic. The graduated cylinder will rotate in the frame.
10/16/2009 6:20:00 PM •
Mitutoyo...
•
Answered
on Oct 16, 2009
How to reset Mitutoyo 314-351
In order to reset the zero point for your specific micrometer, you will need to have a standard set of pre-set dimensional pin(s). You can check the attached link (page 71 of the Mitotoyo catalog) for the information you need). I guess you could try to find or make a pin with the same dimensions as those noted on the catalog page, but if you're using this in a manufacturing setting, you might have no choice but to purchase a set of gauges for calibrating your micrometer.
The only other option is to contact the manufacturer for an alternative method, but I doubt they'll be able to provide any alternative, as precision setting of the zero point is required for accurate readings with this specialty micrometer.
http://www.mitutoyo.co.jp/eng/products/micrometer/Micrometer_2.pdf
7/28/2009 8:55:08 PM •
Mitutoyo...
•
Answered
on Jul 28, 2009
How to measure surface finish at the bottom of a deep pocket?
Machinist, Inspector, Tool & Die Maker, for A.B.B Raymond Division, 1987-94
You need a Portable Surface Roughness measuring tool. Mitutoyo
is one maker of these. Be prepared for a $$$$$$$$ shock, as these babies aren't cheap!
SJ-201, SJ-301 and SJ-400, are three examples,
1.http://www.directindustry.com/scripts/IDPHeader.php?s=4906&URL=http%3A%2F%2Fwww.mitutoyo.co.jp%2Feng%2Fproducts%2Fkeijyou_hyomen%2Fhyomen_01.html&IDVisite=293213&MotCle=&RefCat=&IDProduit=12095&IDProdSource=&SourceType=Produit
(If the above link doesn't work for you, then try this one,
http://www.directindustry.com/prod/mitutoyo/roughness-tester-4906-30234.html
Scroll down the page, and click on -> Portable Roughness Tester)
5/19/2009 7:36:46 PM •
Mitutoyo...
•
Answered
on May 19, 2009
Need user manual for w5746
Same exact features, buttons and functions as this manual by Irwin.
http://www.irwin.com/uploads/documents/36_laser_tape_25.pdf
Will one of the newer sensors work in place of my 1457 sensor?
It's possible that one of the newer sensors could work in place of your 1457 sensor, but it depends on the specifications of the newer sensors and the compatibility with your base unit. The I MAX1457 sensor, which is a highly integrated analog-sensor signal processor optimized for piezoresistive sensor calibration and compensation. However, I have no information about its compatibility. If you're looking for a replacement sensor, I suggest contacting the manufacturer of your base unit to inquire about compatible sensors. Alternatively, you can check the user manual of your base unit to see if it lists compatible sensors. Garage door opener sensors are not universal. Safety sensors can only communicate with garage door openers from the same brand.
Not finding what you are looking for?