20 Most Recent
Black & Decker 8 Inch 12 Volt Cordless String Trimmer And Edger #CST800 - Page 6 Questions & Answers
How do you set barometer
Hi George:
I'm used to barometric pressure as related to altimeter setting in aircraft, but the principal is the same.
For an altimeter, If you know the elevation (above sea level) that you are at, and you set the altimeter to that altitude, the barometric pressure showing on the altimeter will be the current barometric pressure.
If you have a barometer without an altimeter, someone would have to provide you with the current setting. That would probably be your nearest weather station, airport, or your computer.
Here's a link to one.
http://weather.gc.ca/marine/weatherConditions-currentConditions_e.html?mapID=02&siteID=14300&stationID=46131
Pressure and tendency refers to barometric pressure.
If you reply as a COMMENT to this post I will try to assist if possible.
Cheers.
Is there any way to change the battery on a Trumeter 5505E measuring whee
5505E MEASUREMETER BATTERY CHANGE (3V CR-2032)
REMOVE WHEEL AND SHAFT BY GENTLY PULLING AXLE OUT OF UNIT.
DRILL OUT 7 PLASTIC HEADS WITH 3/16 DRILL BIT. (ABOUT 1\8 DEPTH)
SPLIT TWO SIDES OF CASE AND REMOVE HANDLE.
SLIDE OUT CLEAR PLASTIC CONTROL UNIT. PUSH DOWN ON BUTTONS AS YOU REMOVE SO AS NOT TO DAMAGE THEM.
PUSH DOWN SLIGHTLY TOWARD THE CASE ON LOCK TABS WHILE GENTLY PULLING CASE APART. START ON ONE END AND WORK YOUR WAY TO OTHER END. KEEP GASKET INTACT. OPEN CASE.
THERE IS A "Y" SHAPED RETAINER HOLDING IN THE BATTERY. WITH NEEDLE NOSE PLIERS, CAREFULLY SLIGHTLY SQUEEZE THE BOTTOM OF THE "Y" AND PULL UP GENTLY. YOU CAN NOW REMOVE THE BATTERY AND INSTALL THE NEW ONE. PUSH RETAINER DOWN TO LOCK BACK IN.
MAKE SURE GASKET IS IN PLACE AND PUT CASE BACK TOGETHER, MAKING SURE WHEEL ADAPTER IS IN PROPER PLACE. TURN ON AND TEST CONTROL UNIT AND TURN WHEEL ADAPTER TO MAKE SURE UNIT IS WORKING PROPERLY.
SLIDE CONTROL UNIT BACK IN BEING CAREFUL OF THE BUTTONS. RE-ASSEMBLE HANDLE AND PUT THE TWO SIDES OF THE CASE TOGETHER. I USED THREE PIECES OF ELECTRICAL TAPE TO HOLD CASE TOGETHER. ONE ON THE TOP BETWEEN THE TWO HOLES, ONE ON THE BOTTOM JUST ABOVE THE DISPLAY, AND ONE IN THE MIDDLE.
PUT THE PLASTIC PIECE IN THE HOLE AND LINE UP. MAKE SURE BOTH O-RINGS ARE ON THE AXLE SHAFT. GENTLY INSERT AXLE ALL THE WAY IN WHILE ROTATING IF NECESSARY.
I WAS SO HAPPY I HAD IT ALL BACK TOGETHER AND WORKING, I HADN'T TAKEN ANY PICTURES AND I DIDN'T FEEL LIKE TAKING IT ALL APART AGAIN. MIGHT ADD PICTURES LATER IF NEEDED. I HAD BEEN LOOKING FOR YEARS ON HOW TO CHANGE THE BATTERY, AND I FINALLY MADE UP MY MIND THAT I WAS GOING TO DO IT.
JMS 10-20-2020
I have a new XC0436 weather station that is showing time/date 12 hours behind. Tried everything possible but apart doing a manual setting the sync setting is wrong
While trying to setup internet time syncing on my new XC0436 I found this question. The answer from Fred is a bit brief so I thought I should add some details. When the XC0436 is synced to an internet time source it gets the time in UTC. To convert this to local time it uses a manually entered offset. The user manual lists the following steps to adjust the offset:
1. press and hold CLOCK SET key for 2 seconds to enter time set mode
2. the first value displayed is the offset (it appears that only whole hours are possible)
3. press the up or down arrows on the back to adjust the offset (e.g. 08 for Hong Kong)
4. press and hold the CLOCK SET key to confirm and exit
I have an Eddie Bauer Wireless Thermo Clock model
Re: Eddie Bauer Wireless Thermo Clock - Model 0465
TIME ZONE SETTING
The default time zone is PACIFIC (P). lf your location is not in the Pacific zone, set the time zone as follows:
1. In normal time mode, press the "[,4ODE" key to enter the alarm time mode. 2. ln alarm time mode, press and hold the ADJ . 'Cl"F" key for 2 seconds to enter the time zone setting mode.
3. Press ihe "ADJ "C/'F" key to select the proper time zone: P=Pacific
M=Mountain C=Central E=Eastern.
4. Press the f,'lODE key to save and exit the time zone setting mode, or let it exit automatically 30 seconds later without pressing any key.
This sequence fixes my thermo clock. Follow step-by-step ......
Sent via Mobile GMail Services
06.20.2021 KJ Bleus Parsons
---------------------------------------
Not finding what you are looking for?