Top 20 Hobart HL600 Legacy Stand Mixer - Page 7 Questions & Answers

You would need to replace the Alternator to obtain the lower operating voltage.

The safety switch activated or damage

Because either the low speed windings or low speed control is kaput.

Steve I dont know that that is necessary. I have 2 a big heavy monster and a little #12 and I check for full and keep going. I only use mine in winter for sausage and its 50# in 120 sec. not much wear and tear on the lube. I know Hobart has a good web and mobile service here. Mine are Old and I'm guessing yours are too. http://www.hobartcorp.com/

08/03/2007 model number

Hobart service company in Spokane, WA, and he told me that any 40 weight, non-detergent oil will work. He also suggested it is far cheaper to just get it at a local auto parts store.

Check the coil in the contactor is getting power . If it is the coil is gone and if not a safety switch or switch is not working somewhere.

Google perhaps a fuse is blown something was to heavy or something was under tension to the power supply that so the machine did not get the required voltage by too much taxation by other devices on the power line group

go google and type in--hobart food mixer manufacturer and there are pages of hobartfood.com.au and hobartcorp.com/products/food-prep/mixers / all of these pages will have a contact us section where there will be phone numbers and e-mail addresses contact them direct in a area /country near you and see what is available

Id contact Hobart. the serial # doesnt use a date code. Hobart Contact Us

It is overcurrent issue due to low supply volt or batch size too big or VFD is faulty.

Kitchenaid.com

Need pictures to look at to help.

It is over current issue due to low supply voltage or batch size too big or frequency drive shorted.

http://thesmartpartsestore.hobartservice.com/

Baldor no longer manufactures that motor. Hobart would have to install a kit that includes every electrical component in the machine. Be careful if you find a used one, they have a very fragile encoder on the rear of the motor.

images for hobart gwx2 manual & wiring

Lora I see lots of the same question from you and notice you are asking in the food mixer category. Might be time to ask in the oven category. Another plan would be to contact an authorised Hobart service agent and see if they can help you. Normally they will have access to service data.

Hi Bill I may be wrong here...... But I've been around Electricity for a long time. Have Never seen a device that does phase conversion. A Building site or home will either have Three Phase or Single Phase Power Available BUT...A portable (Hired) generator could be "three phase" and you could use any one of those phases individually or all three phases. I have 3 Phase supply to my house! But I use 230 volt Single Phase for appliances. My Bore Pump uses a 3 Phase Motor, (so with a voltmeter it would read about 440 vAC to the pump motor). Some Further Info: A GENERATOR is basically a motor used the opposite way. Rotate a motor and it Generates. The Phases refer to the THREE Windings in the supplying generator in your suburb. A Large Magnet passes each winding in sequence giving you the three ripples in the supply. Our houses can choose to have 1 Phase or Three Phases from the street when you set up your electric supply. So... to confirm, look at the wires on the supply poles to the premises. Usually three in our area (Oz) Most people are not aware that a car Alternator is actually three phase. The Rotor is the magnet that rotates. The only difference with an Alternator is that each "Phase" is connected to 2 Diodes (6 total) to convert the three phase to DC to charge the vehicle. The Regulator controls the voltage to the Rotor, thereby controlling the output. So.... An Alternator could in theory supply 3 Phase in a mobile generator. Custom Made. Constant speed would determine the frequency of 50Hz or 60Hz. Not sure what country you are in Hope this Helps or gives you food for thought! Three phase electric power

If your mixer's power is three phase, switch any two of the power leads to get it to run, turn the other way