20 Most Recent Hobart 40 in. AM14-254 Free-standing Dishwasher Questions & Answers


Hello & Welcome to FixYa

The solution will be replacement with a new one, as I checked everywhere and its parts are not available until you buy a old unit and get its parts replaced with this one. Please get back to me if you have any other questions.

Kevin

Hobart 40 in.... | Answered on Jan 20, 2011


It pulls off. Just use a small/medium sized gear puller and it'll come easily ( there is a lip on the impeller for the purpose of pulling).

Hobart 40 in.... | Answered on Dec 24, 2010


t is your overflow .. there is water under in the dishwasher tray or the float is stuck in the up position.
you will have to remove the toe panel and get the water out from the tray or free the float ( sometimes soap gets under and sticks the float in the up position...

Hobart 40 in.... | Answered on Dec 11, 2010


I love these machines. Keep it and fix the leak.

If you have a leak. You have to find out where it is coming from. Dripping water from the bottom of tank can be coming from a number of different places and at different times thru out the cycle. The rinse cycle or wash cycle or all the time.

The first place to check is the pump. It will leak during the wash cycle. Especially from the top gasket. This one commonly goes out.

The pump motor shaft seal will leak all the time but will drip from motor, not the tank area. You want to fix this before it ruins your motor bearings or motor.

But since you have a corner machine, the first thing to check is the rear door panel. This is were your door would be if you had a straight thru machine instead of a corner machine. It has teflon guides just like your actual doors and they do leak at times or all the time if the guides are
not sealing. IF food particles accumilate at the bottom of that panel it blocks the water from running back into machine and instead, onto your floor from the bottom of tank areas. This is anther common leak.
The teflon guides should be replaced if they have cracks in them or are brittle and flaking apart. Sometimes they slide down and can be push back up from inside the machine. In either case, you will need to clean all the crud from that back panel edge. Usually thats all I do to fix that leak is just clean it up and push those guides out to outside edge with the tip of my screwdriver to tighten the seal between them and the channel.

Hope that helps!

Hobart 40 in.... | Answered on Jul 15, 2010


Hi

Thanks for using FixYa. Dishwasher not draining properly or not draining at all issues can arise due to different reasons. Usually, these issues are related to kinked hoses, knocked out disposer unit (if connected with the dishwasher drain hose) & clogged drain pump & filter.

Also note that dishwashers do not drain completely after a finished cycle and this is normal. Dishwashers are designed to leave some water in the unit to ensure that the heating element doesn’t overheat. If you suddenly begin to experience a large amount of water being retained in your dishwasher, you have a problem. Some of the most common reasons include that the drain hose isn’t working properly, the drain pump isn’t working correctly, or possibly there is a plumbing problem in your home’s drain lines.


First check whether the drain is not clogged or blocked and the line is not kinked. Check all the hoses for blockages & also clean the air gap. Has the disposer been replaced recently? If so, chances are the knockout is still in place. Simply remove the drain hose from the disposer, and knock out the plug. If the disposer has not been replaced, try removing the drain hose from the disposer and use a wet-dry vacuum (prepared for water, of course) to **** any water (and hopefully anything else) from the drain line. Then reconnect the hose, and test the unit. If you have checked the air gap and the drain hose and can’t locate the problem, then it is an issue with the drain pump of the dishwasher.

Please do accept the solution if the issue is resolved or else revert for further assistance.


Thanks

Rylee

Hobart 40 in.... | Answered on Dec 11, 2009


Did you solve your problem?I'm a hobart tech and repair these often.Let me know.

Hobart 40 in.... | Answered on Apr 12, 2009


If you see F04, it is likely that there is water inside the air trap or pressure transmitter for wash tank is faulty. Sometimes it happened due to water inside pressure pipe.

Hobart... | Answered on Jun 30, 2020


hello and welcome

unfortunately all FO4-2 errors need a service call

Pressure transmitter "tank" defective.

https://www.manualslib.com/manual/871918/Hobart-Fx-Series.html?page=17

Hobart... | Answered on Jun 29, 2020


IT HAS TO GET POWER FROM WALL SOCKET DOES IT NOT ?

Hobart... | Answered on Apr 29, 2020


https://www.youtube.com/watch?v=e2Bgh_UDpPM

https://www.caterkwik.co.uk/shop/downloads/HOBARTECOMAXH602_ecomax402502602-service-manual.pdf

Hobart... | Answered on Apr 17, 2020

Not finding what you are looking for?
Hobart 40 in. AM14-254 Free-standing Dishwasher Logo

Popular Tags

17 questions posted

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6133 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hobart Dishwashers

  • Hobart Dishwashers

Most Popular Question

ithink its 1977 year

  • Dishwashers
Loading...