20 Most Recent Hobart 42 in. AM14C-154 Free-standing Dishwasher Questions & Answers


If it's drain water and filling with water at the same time your drain hose is lower than the water fill line of the washer. try raising the drain hose up higher

Hobart 42 in.... | Answered on Apr 30, 2017


the pressure regulator turn screw clockwise to turn up pressurre.But the line strainer could be plugged do you have bad water.Is the gauge correct.you can get a gauge at home depot for cheap.0 to 60 psi should be ok.usually made by watts.you dont have to use a hobart gauge.

Hobart 42 in.... | Answered on Apr 23, 2011


www.hobartservice.com Click on "Locate an office" and type in your zip.

Hobart 42 in.... | Answered on Aug 13, 2010


You can get the parts at your local Hobart office. It would be very costly to change the unit to single phase.
www.hobartservice.com Click on "Locate an office" and type in your zip.

Hobart 42 in.... | Answered on Aug 13, 2010


www.hobartservice.com Click on "locate an office" and type in your zip.

Hobart 42 in.... | Answered on Aug 13, 2010


You may have installed the stainless float retainer backwards. The hook on the retainer that holds the float faces the tank wall and fits into a flat on the probe. This prevents the rotation and will better secure the float.

Hobart 42 in.... | Answered on Aug 13, 2010


Call them back!
I assume that he sent you the parts for the new version door switch assembly or He used the wrong ML# when looking up the parts. The ML# is the material list they used for each version of the machine over the years. When they make changes to a machine, like updating the door switch, they issue whats called a TSB (technical service bulletin) to each technician and parts person. Nowadays I think its all computer based. and they dont issue the paper manuals that they used to issue. It was much easier to track way back when. not so much today though.

Hope that helps.

Hobart 42 in.... | Answered on Jul 15, 2010


Hello,
All Hobart AM-14 come with a vacuum breaker which prevents any back flow from occurring.
Regards

Hobart 42 in.... | Answered on Mar 12, 2010


no there are no resets on this d/w. open the control box door, ck. the fuse's inside on the trans. and on the control board. if any are burnt replace, you need to find out where you are losing your voltage,by using a meter

Hobart 42 in.... | Answered on Jan 19, 2010


What is the model and ml number of your dishwasher?Its located on the data plate,let me know.

Hobart 42 in.... | Answered on Nov 18, 2009


Can you confirm if you have an AM14 or AM15. Check the data plate and give the Voltage spec., ML number, if you have it.' Please confirm what you mean by the wires are trip.

Hobart 42 in.... | Answered on Oct 05, 2009


Removed the solenoid assy, loosened the valve assy a little and re-tightened. The valve now works. Next step is to dis-assemble the valve and try to clean it out.

Looking for a replacement part, but the AM14 model is old and parts are hard to find. The specs say its a 20-30 V coil and the AM15 appears to use a 115V part.

Possibly the o-ring inside the valve can be replaced. I did notice that blackish water came out of the valve assy when I looosened it.......

Hobart 42 in.... | Answered on Oct 02, 2009


Most AM-14's use a Parker 3/4" solenoid valve. Readily available from Johnstone Supply, International Commercial Supply, Franklin Machine Products, or Hobart (same part, more expensive). Comes as a whole kit, new diaphragm, strainer, o-ring, and plunger (MUST BE CHANGED).

Hobart 42 in.... | Answered on Sep 12, 2009


change the company

Hobart 42 in.... | Answered on Sep 12, 2009


If water is running even with the machine turned off then your solenoid valve needs to be cleaned out or rebuilt. This valve is in the back top of the machine by the gauge.

Hobart 42 in.... | Answered on Aug 08, 2009


There are two possible reasons for the situation as you describe it: 1. Water-inlet valve The water-inlet valve lets water enter the machine. If this valve is defective, you need to completely replace it. It's usually located behind the lower access panel on the left or right side. It's the device with the main water line (usually copper) from the house, a rubber tube to the dishwasher, and two wires attached to it.
2. Float switch The float switch is a small electrical switch that's located right below the dishwasher "floor." Above the switch, on the inside of the dishwasher, is a plastic cylinder that floats up as water fills the dishwasher. If this switch is defective, or if the plastic float gets caught or trapped in the raised position, the water can't enter the dishwasher. If the float switch is defective, you need to replace it.

If you are mechanically inclined you can repair either of these but if you are not you will have to hire it done. Now that you know it is one of two problems you can tell the repairman ahead of time and get a price on the repair. Then shop around for the best price.

Hobart 42 in.... | Answered on May 08, 2009

Not finding what you are looking for?
Hobart 42 in. AM14C-154 Free-standing Dishwasher Logo

Popular Tags

32 questions posted

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Cindy Wells

Level 3 Expert

6164 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hobart Dishwashers

  • Hobart Dishwashers

Most Popular Question

in replacing float

  • Dishwashers
Loading...