Top 20 Yukon 24021 Monocular Questions & Answers

these units need a very small amount of light to work at all, They amplify this small amount of light, with no light at all they have nothing to amplify! the infra red is a source of light so it can amplify that, At night they amplify street lighting or moonlight or starlight etc, hope this helps,

Hello, take some switch cleaner--Radio Shack- and spray just a small amount into the switch. Did you installed the battery correctly with the polarity be correct. Does the battery compartment have any type of corrosion? If this does help then there is something else wron with it. stewbison

Don't IR illuminator in the dark room. Turn on a small light in one of the corner; such as, a small light bulb. increase ambient light a little at a time until you can focus. You flooding the dark room with IR illumination which will reflect everywhere in there. This might take care of the fuzziness in the monocular. stewbison

You can download a manual from THIS LINK

The page is the manual in HTML, but you can download a .PDF file from a link at the top. Note that this file is named "5", and your computer won't know what kind of file it is, so you have to rename it "5.pdf" to get your PDF reader to open it.

Define 'clear'.
Is it blurry? Focus the scope or clean the lenses.
Is it distorted? Don't know how to fix. Especially if the lens is cracked/scratched etc.
Is it dark/snowy? Put fresh batteries in.
Do you see black spots in the tube? Don't worry, certain amount of these are quite acceptable.
Anyway: It's a night vision for pete's sake. The picture won't ever be like the one on normal binoculars.

Hello, don't worry about it. It is HV to the image intensifier tube. The battery voltage goes through control circuit then to ccfl inverter (here is were dc voltage is switch on and off and switch dc voltage is step up by toroid coil that has two input and only two out puts). By impulsing the coil with two different switch dc voltage on the input this make the current lag the two different phase voltage by 90 degrees. Here is where the strange noise is coming from. The toroid coil is encased in iron case and if half of this iron case is loose, it makes case vibrate so the noise.


Now, the voltage come out of the toroid coil is switching dc (one could call it AC because that what AC voltage is, it switch between positive to negative) this voltage is about 300 to 900 switching DC voltage. This voltage will be applied to a 1/2 wave voltage multiplier (this voltage multiplier with have anywhere four four stages to 10 stages depend on what the input voltage to multiplier is.

Low the voltage out of the ccfl inverter the more stages the multiplier will have.



Now, the voltage multiplier will double the voltage per stage to need image intensifier tube voltage of 12000 to 45000 volts---DC switching or AC what ever one wants to call it. This voltage will bit you but it doesn't have a lot current associated with it, the current would be in the 10 to 15 ua (micro-amps) 1/10X6 amps.



Now, you know. GB...stewbison

Visit your local gun shop and have them order them.

copy and paste https://www.bhphotovideo.com/lit_files/90269.pdf

its just 1-2-3-4- with the port bank being 2-4 starting at the top and the starboard side being 1-3. They're all the same be it V-4 or V-6. 6=123456 60* and 90* are the same

If the batteries are worn out or have not be put in properly. You may have to resync your devices the the USB receiver.

All question need FULL 'make model (what it is)'. You posted to optics, so let's guess is a telescopic rifle sight? It is impossible to see and movement as the crosshairs move such a tiny amount. Half a millimetre in the sight is 10 feet at the target. The only way to zero in sights is on a fixed bench rest at the range. If you really think they are faulty, return them to the maker for repair.

Question edited for clarity. Duplicate Question deleted. It doesn't seem to be available https://www.google.com/search?q=Franklin+Chef+FCE-42R+manual ..

I can find no reference to a company called 'SIFT' and a model called 'SWPA', so sourcing is difficult. You can buy rubber eyepieces easily. https://www.google.com/search?q=7x50+binocular+eyepieces The search query would be make model eye piece replacement ..

900,000-925,000 made in 1956 https://www.google.com/search?q=savage+stevens+model+94+serial+number+lookup ..

Question edited for clarity.Question moved from Computers to Telescopes.The manual is not found online, but all refractor telescopes of that type work the same.https://www.google.com/search?q=Magnicon+stargazer+234+manualhttps://www.cloudynights.com/topic/431604-is-it-worth-reworking-my-60mm-scope/The Tasco Manual should suffice. I had one!https://www.google.com/search?q=tasco+refractor+telescope+manual..

Yes, you can get a replacement stove top for your Whirlpool clean top stove, and it depends on the model and the availability of parts. You may contact Whirlpool customer service or check with a local appliance parts supplier to see if they have the replacement stove top in stock. As for the installation, it will depend on your level of experience and comfort working with appliances, as well as the specific model of your stove. Some stove tops may be relatively easy to install, while others may be more complex and require professional installation. Generally speaking, installing a replacement stove top can be a difficult and complex task that requires a certain level of technical knowledge and expertise. It's recommended to consult the stove's user manual or contact Whirlpool customer service for assistance with installation instructions or to find a professional to do the installation.

Whether or not it's worth it to buy a replacement hand control for your NexStar 90GT telescope depends on a few factors:

1. How often do you use the telescope? If you use it frequently and rely on the hand control to find objects in the sky, then it may be worth it to invest in a replacement.
2. How important is the hand control to your observing experience? If you're comfortable manually finding objects in the sky and don't necessarily need the hand control, then it may not be worth the expense.
3. Can you find a cheaper alternative to the official replacement? Sometimes, third-party sellers may offer hand controls that are compatible with your telescope at a lower price.

Ultimately, it's up to you to decide whether the cost of the replacement hand control is worth it based on your individual needs and preferences.

Try the maker direct. https://www.google.com/search?q=Mead+binocular+camera+charger+replacement It uses a non standard connector according to this https://www.reddit.com/r/techsupport/comments/4gacs5/can_anyone_identify_this_strange_usb_port/ ....

Hi, please call the manufacturer and ask them to email you the product's manual. As for parts, you search through Amazon and Alibaba for different parts for your product. Thank you.

No problem Robert you caught me late at night and very tired after a trying 14 hour shift here. My first answer showed lots, but the wrong type. After you pointed out my error, I used this modified my search query which forces the words 'reflector telescope' in the results and next to each other. I went through all 4 pages, but mentions of those two words are in the context of "not suitable for 'reflector telescope'". The only thing I can thinking of is to phone a shop that specialises in telescopes and ask. They may know of the only one that is available. It may also be dependent on your make and model. https://www.google.com/search?q=90+degree+adapter+for+a+%22reflector+telescope%22 I ground a telescope mirror at school! ..