KitchenAid KEMC378KSS Electric Double Oven - Answered Questions & Fixed issues

The oven lights are 12-volt, 5-watt maximum halogen bulbs. Theywill come on when the oven door is opened. On double ovenmodels, both upper and lower lights will come on when eitherdoor is opened. The oven lights will not work during the Self-Cleaning cycle. When the oven door is closed, press OVENLIGHT to turn them on or off.To Replace:Before replacing, make sure the oven is off and cool.1. Disconnect power.2. Remove glass light cover by grasping the front edge andpulling away from oven3. Remove bulb from socket.4. Replace bulb, replace bulb cover by snapping back into wall.5. Reconnect power.

switch for the door is not engaging so as to shutoff this message.

I suggest check the next video about How to change your magnetron tube in your GE Microwave...



Hope helps.



">

This worked like a charm ... actually it's easier than you might think. Just a few screws and a few tugs. Give it a shot.. I found a 10W (G4 style ... you'll see the difference when you get to the store) replacement bulb at Home Depot for $6:

1) Turn off power to the unit
2) Open the lower oven door
3) Remove the side trim screws and pull the trims down and out.
4) Remove 2 screws on the sides of the control panel.
5) Open the Microwave door. Remove the 3 screws on the Air Vent Plastic Cover on top of the microwave. You can then remove the Air Vent Cover by pushing the control panel up and pull out slightly at the bottom.
6) Remove the 4 screws on the Air Vent Plastic Cover on top of the lower oven and remove the Air Vent Cover. (You may have to remove the left under side bracket of the Microwave door temporarily just for the Air Vent Cover to clear the screw of the bracket. Re-secure the side bracket of the Microwave door panel as the front panel may fall)
7) Remove the 2 screws which held the Microwave unit in place behind the Air Vent Cover on step 6.
8) Wiggle the Microwave unit out about half way to expose the light bulb unit on top center
9) Wiring to the Control Panel will prevent you from pulling the Microwave unit out any further. And you don't want to do that as the unit may fall. Space is cramped, but working carefully with your fingers or pliers you should be able to release the springs which held down the light bulb unit and change the bulb.

Here is a simpler method from the same website mentioned in solution #1:
1) Turn off power to the unit
2) Open the lower oven door
3) Remove the side trim screws and pull the trims down and out.
4) Remove 2 screws on the sides of the control panel.
5) Open the Microwave door. Remove the 3 screws on the Air Vent Plastic Cover on top of the microwave. You can then remove the Air Vent Cover by pushing the control panel up and pull out slightly at the bottom.
6) Remove the 4 screws on the Air Vent Plastic Cover on top of the lower oven and remove the Air Vent Cover. (You may have to remove the left under side bracket of the Microwave door temporarily just for the Air Vent Cover to clear the screw of the bracket. Re-secure the side bracket of the Microwave door panel as the front panel may fall)
7) Remove the 2 screws which held the Microwave unit in place behind the Air Vent Cover on step 6.
8) Wiggle the Microwave unit out about half way to expose the light bulb unit on top center
9) Wiring to the Control Panel will prevent you from pulling the Microwave unit out any further. And you don't want to do that as the unit may fall. Space is cramped, but working carefully with pliers you should be able to release the springs which held down the light bulb unit and change the bulb.

By the way, the bulb is Osram 64405S. It's available online for about $2.00 plus shipping.
See more info. at: http://www.howtomendit.com/answers.php?id=51232

Hi,

Here is a tip that will help you to figure out what is wrong with your Microwave Oven....Microwave Oven Basic Troubleshooting Tipsheatman101

FixYourBoard.com will test and remanufacture the oven control board in this model. We also have touchpads ( aka keypad membranes ) available for this model. Each rebuild comes with a two year warranty. Reach out to us at 512-355-1108 or [email protected]

This typically indicates an issue with the touchpad or control board. Here are some steps you can take to troubleshoot and potentially resolve the issue: Check the Cable Connection: The error code could be due to the touchpad cable being unplugged. Ensure a proper connection between your appliance's touchpad and the control board. Power Reset: You can try resetting the oven by turning off the fuse or circuit breaker, waiting for 1 minute, and then turning it back on. Repeated power restarts may allow the oven to reset and resolve the issue. Replace the TouchPad or Control Board: If the connection is fine and the error code persists, the issue might be a malfunctioning touchpad or a fault on the control board. In such instances, it's recommended to replace these parts entirely. Please note that this should be done by a professional to ensure safety and correct installation.

Here is the terminal block for a freestanding range, Page 8 onwards. https://www.kitchenaid.com/content/dam/global/documents/201808/installation-instructions-w10694026-reva.pdf https://www.google.com/search?q=kitchenaid+kebc208kbl0+wiring+diagram+pdf I also checked for a Service Manual, but KitchenAid don't release them. ..

Read off the power consumption of each oven and other equipment being fed from the cooker supply and have an electrician check the size of your cooker feed cable and main cooker breaker. If the cable is not thick enough for the oven, you cannot increase the breaker size! The breaker may of course be faulty, measure the current draw as the brealer trips.

Question edited for clarity, the MAKER, and 'what is is'. Question moved to KitchenAid. You may have a bad sensor. Not sure Amazon is the best place to buy. A lot of parts are no longer available, so you should perhaps be thinking of a replacement? https://www.partselect.com/Models/KERA205PSS5/Sections/CHASSIS-PARTS/?ModelID=679473&ModelNum=KERA205PSS5&mfgModelNum=&ManufactureID=3&Selected=N7FWPBQ3&Position=1&mfg=Whirlpool&Type=Range&Mark=1 Is the fan spinning okay? This suggests a bad fan. It has a small circular element around the fan. https://www.google.com/search?q=kitchenaid+keri203pbs+oven+not+reaching+temperature ..

sounds like overheated bad control board or transformer

see if voltege to board

https://www.coastparts.com/lookup/278376

lots of videos https://www.google.com/search?q=replace+the+oven+inner+glass+for+my+Kitchenaid+ykerc507ew2 ..

WE HAVE NO INFORMATION AND SEBSTITUTE PARTS SORRY

Do you have a flame sensor ? As it sounds like the flame sensor is not clean . Or its cracked and not sending a signal back to the spark module . I would also check the connetions are clean and tight .

I have the same issue. Any tips for solution?https://get-mobdro.com/home

Request the Superba model kebc107kss03 manual directly from KitchenAid.

Is it possible you've blown a breaker? Probably a double-breaker, 220V.