Top 20 KitchenAid KEBC277 Electric Double Oven Questions & Answers

Hi,
Cycling the power off and then on again will sometimes reset it...often you will have to call the customer service number to get the steps to take to unlock that...

Also check out this tip...

http://www.fixya.com/support/r3969401-self_cleaning_oven_problem

heatman101

here is my video might help you.

Yes the inner door glass is a replaceable part and the door will have to be disasembled but not replaced. I can help with sourcing any parts for you since you used a premium post.

Clock error it happens when the external clock goes out of sync with the internal clock nothing to worry about it should have went away on its own after about 30 seconds

This typically indicates an issue with the touchpad or control board. Here are some steps you can take to troubleshoot and potentially resolve the issue: Check the Cable Connection: The error code could be due to the touchpad cable being unplugged. Ensure a proper connection between your appliance's touchpad and the control board. Power Reset: You can try resetting the oven by turning off the fuse or circuit breaker, waiting for 1 minute, and then turning it back on. Repeated power restarts may allow the oven to reset and resolve the issue. Replace the TouchPad or Control Board: If the connection is fine and the error code persists, the issue might be a malfunctioning touchpad or a fault on the control board. In such instances, it's recommended to replace these parts entirely. Please note that this should be done by a professional to ensure safety and correct installation.

Here is the terminal block for a freestanding range, Page 8 onwards. https://www.kitchenaid.com/content/dam/global/documents/201808/installation-instructions-w10694026-reva.pdf https://www.google.com/search?q=kitchenaid+kebc208kbl0+wiring+diagram+pdf I also checked for a Service Manual, but KitchenAid don't release them. ..

Read off the power consumption of each oven and other equipment being fed from the cooker supply and have an electrician check the size of your cooker feed cable and main cooker breaker. If the cable is not thick enough for the oven, you cannot increase the breaker size! The breaker may of course be faulty, measure the current draw as the brealer trips.

see if voltege to board

https://www.coastparts.com/lookup/278376

sounds like overheated bad control board or transformer

lots of videos https://www.google.com/search?q=replace+the+oven+inner+glass+for+my+Kitchenaid+ykerc507ew2 ..

Question edited for clarity, the MAKER, and 'what is is'. Question moved to KitchenAid. You may have a bad sensor. Not sure Amazon is the best place to buy. A lot of parts are no longer available, so you should perhaps be thinking of a replacement? https://www.partselect.com/Models/KERA205PSS5/Sections/CHASSIS-PARTS/?ModelID=679473&ModelNum=KERA205PSS5&mfgModelNum=&ManufactureID=3&Selected=N7FWPBQ3&Position=1&mfg=Whirlpool&Type=Range&Mark=1 Is the fan spinning okay? This suggests a bad fan. It has a small circular element around the fan. https://www.google.com/search?q=kitchenaid+keri203pbs+oven+not+reaching+temperature ..

WE HAVE NO INFORMATION AND SEBSTITUTE PARTS SORRY

Do you have a flame sensor ? As it sounds like the flame sensor is not clean . Or its cracked and not sending a signal back to the spark module . I would also check the connetions are clean and tight .

I have the same issue. Any tips for solution?https://get-mobdro.com/home

Is it possible you've blown a breaker? Probably a double-breaker, 220V.

Hello Susan Bailey, Typically "THEY" do... It would be really great to know if we are talking about a USA domestic product... or another NATIONALITY. Other countries normally have FUSES in the appliance cords. Find your MODEL NUMBER and go to a PART/SPARES supplier ( I like appliancepartspros.com ) -> appliancepartspros.com If this is a "MICROWAVE" the FUSE will start popping because the MAGNETRON has deteriorated and is CONSUMING it's own energy. I can be a LOT MORE specific if you provide a model number (pretty please). Read minds... Cannot rally do...!! https://en.wikipedia.org/wiki/Carnac_the_Magnificent

Possible Solutions

Reset power to the product:

There may be a problem with the Oven Appliance Manger Control or the associated wiring.

• Power unit down by turning off the circuit breaker(s) for one (1) minute.
• Power unit up by turning on the circuit breaker(s).
• Monitor the oven for one (1) minute to ensure the error code does not display again.
• Verify oven operation.

Still need help? Call or schedule service.

In our case, the error code was displayed on a KitchenAid microwave/oven combo. It turned out to be a $4 fuse called the "Main Cavity Fuse". Good luck.