20 Most Recent American Standard Cadet 3 Right Height Elongated Toilet by - ADA Compliant - Page 8 Questions & Answers

0helpful
1answer

New toilet 540 fluidmaster water in tank keeps topping off every half hour

The problem may be the flapper that seals between the tank and bowl is leaking or the overflow pipe may have a crack in it. I wouled replace the flapper first and check the overflow pipe for cracks. Hope this helps. Bob
12/1/2014 3:00:08 AM • American... • Answered on Dec 01, 2014
0helpful
1answer

Hello i am trying to locate Pump #752538-300.

I have one. Call me at 510 559 0623.
10/17/2014 9:27:26 PM • American... • Answered on Oct 17, 2014
0helpful
1answer

Repair crack in floor of acrylic shower

Hello their is a product called Plasweld,it comes in a handy tube, Carefully scratch along the crack to allow the weld to come flush with the surface of the shower tray,MUST BE PERFECTLY DRY! squeeze into the crack and it will find its own level ,this produce actually welds the plastic together Good builders merchants should stock this item.GOOD LUCK
9/15/2014 12:00:54 PM • American... • Answered on Sep 15, 2014
0answers
0helpful
1answer

Toilet Tank overflow wasting water need manual.

Adjust the float so water level stops at 1/2" below top of overflow pipe.
8/23/2014 7:58:19 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

Overflow tube

If you manually pull up on the float of the fill valve will it then shut off? If it does, most likely your water pressure is too high, should be around 60 psi. More then 80 and it won't shut off. You may need to add a restrictor to the fill valve. Most fluid-master units come with one already installed, you could try one of them.
8/23/2014 7:52:21 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

Toilet flushed then dripping sound at floor level

If you;re sure its under the toilet, look for a crack in the base, especially around the retianing bolts, or the wax bowl seal is gone, needs replacing.
8/23/2014 7:45:57 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

Toilet driping sound at bottom after flushing

Either the flapper is not closing completely or the water level is too high so water runs out the overflow pipe. Level should be set at 1/2" below top of pipe.
8/23/2014 7:44:25 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

How to do you reset the float

The older styles have a screw at the end of the shaft where the fill valve is, turn the screw in and out to adjust float arm level. Newer ones have a plastic nut and bolt about midway along the shaft. Turn the nut to loosen slightly, push the float up or down and tighten the nut. Caution: The plastic bolt breaks easily so don't tighten the nut too much.
8/23/2014 7:36:11 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

Fluidmaster 400 instructions

Depends on type. Rubber ones usually are suspended from the seat by an arm on either side, you pull it off the arms and replace the same way. Older ones slide down over the overflow tube.
8/23/2014 7:04:02 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

Flow of water into american standard toilet tank is very slow and does not fill up to water mark

Adjust the level of the float, water level should be about 1/2" below top of overflow pipe. Slow filling can be due to a build up of calcium in fill vale, a partially blocked water valve, the washer many times gets deteriorated by the chlorine in the water, breaks up and clogs the fill line. Also many manufacturers (fluid-master in particular) place water restrictors inside the bottom of the fill tubes, which cause the water to fill much slower.
8/23/2014 7:00:59 PM • American... • Answered on Aug 23, 2014
0helpful
1answer

1.6 toilet will not fill

Make sure the water valve to the toilet is actually letting water into the fill valve. Turn off valve, remove from fill valve, run water into a pan to see pressure and confirm water flow. If water flow and pressure good, replace the fill valve.
8/23/2014 1:07:16 AM • American... • Answered on Aug 23, 2014
0helpful
1answer

How to remove an american standard single lever shower handle?

There should be a allen wrench set screw under the handle at the bottom. just unscrew it and you should be able to work it off...hubby is a plumber
8/7/2014 7:09:17 PM • American... • Answered on Aug 07, 2014
0helpful
1answer

Bottom of bowl is stained very much. Appears to be a defect in the the finish?

Try using one of these A product called Kaboom Bowel Blaster and let it sit in the bowl for a while, then brush clean. This worked for me when others failed. You can try muriatic acid as a toilet bowl cleaner.Again let it sit for a while then brush and flush available from places like Home depot.Sometimes the toilets are not glazed as well as they should be you might call it a defect I call it poor quality control.
8/7/2014 3:38:48 PM • American... • Answered on Aug 07, 2014
Not finding what you are looking for?
American Standard Cadet 3 Right Height Elongated Toilet by  - ADA Compliant Logo

77 questions posted

Ask a Question

Usually answered in minutes!

Top American Standard Home Experts

Mike

Level 3 Expert

4377 Answers

john h

Level 3 Expert

24888 Answers

Ekse

Level 3 Expert

13435 Answers

Are you an American Standard Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

American Standard Home

  • American Standard Home

Most Popular Question

water level in bowl low

  • Home
Loading...