20 Most Recent Leviton Decora Light Dimmer Switch - Page 4 Questions & Answers

0helpful
1answer

Does a leviton slide dimmer switch use regular bulb's

what do you know as "regular " bulbs are they low energy or incandescent
10/11/2018 5:50:39 AM • Leviton... • Answered on Oct 11, 2018
0helpful
1answer

Dimmer slide does not dim

Replace it. They fail and and that is not uncommon. good luck
5/20/2018 4:04:38 PM • Leviton... • Answered on May 20, 2018
0helpful
2answers

I have an old easyset E-600VA dimmer connected on single pole to a ceiling light. I want to replace that with a new Leviton toggle switch with dimming slide.

red never connects to black as that is power to neutral if wired correctly get in a qualified electrician to check the wiring and help you install the unit
5/1/2018 11:36:21 AM • Leviton... • Answered on May 01, 2018
0helpful
1answer

How can I wire 3 Lutron Dimmer switches in a series? Each switch will control a different set of lights. I pig tailed the black power source to each of the dimmers. I ran the black wire from the l

yes, take the white wires off the switches and splice them all together with a wire nut. Run a hot wire to each of the switches and then run the switch leg (black) from each of the fixtures to be controlled to each of the dimmers.
12/18/2017 3:05:53 AM • Leviton... • Answered on Dec 18, 2017
0helpful
1answer

I am trying to wire a Leviton 3 rocker/4 function switch to a fan with fan/heat/light/night lt. There are 3 colored wires out of the back red,black,blue and 2 load screws.

If the two load screws are connected with a tab that is the power in side. The color wires are the load.
11/3/2017 1:27:47 AM • Leviton... • Answered on Nov 03, 2017
0helpful
1answer

I have had several failures of the Leviton Decora

Seems to be a common problem, you're not alone ( read amazon 1 star reviews). They are $22.00 so you will to dispose of it, if Leviton will not warranty it.
10/27/2017 12:20:51 AM • Leviton... • Answered on Oct 27, 2017
0helpful
1answer

Wiring a leviton 5641 so fan & light turn on separate with red & black wires

the 5641 is a dual switch for three way and single pole. If you want the switches to operate the CF. Connect the power to one of the two screws on the right side as you face the switch. then connect one wire to the screw on the bottom left side. connect the other screw to one of the two screws on the top left. This assumes the Red and Black you mentioned are the switch legs going to the CF.
5/1/2017 3:42:09 AM • Leviton... • Answered on May 01, 2017
0helpful
1answer

I have a bedroom switch controlling a ceiling fan (separate speed switch) and a wall switch going to an outlet. I can't get the outlet to work with the wall switch. The fan works fine

You need to verify if there are two wires coming to the wall switch from the receptacle. One should be power in, the other should be power out to the receptacle.
5/1/2017 3:36:47 AM • Leviton... • Answered on May 01, 2017
0helpful
1answer

Wire occupancy sensor to control receptacle

Your description doesn't explain the circuit, the function of the wires or how the switch controls the outlet and whether the switch is a single pole or two-pole switch. Without such details it is difficult to visualise the circuit. I advise before you go further to test the sensor in a known good and correctly wired outlet using a length of cable and a suitable plug for the outlet. It is possible the unit is faulty. If it functions correctly on test you will need to understand the circuit and the function of the wires before you rewire it to assure success.
4/18/2016 2:23:52 AM • Leviton... • Answered on Apr 18, 2016
0helpful
1answer

How do you wire a switch at the end of two lights wired in paralell?

You MUST to interrupt the circuit between the the power source and the lamps. The switch is in series with the lamps that are in parallel as shown below: 25955740-5h2dbzfnzltxrngjp2sobitb-5-0.png
11/12/2015 9:16:55 PM • Leviton... • Answered on Nov 12, 2015
0helpful
1answer

Why does my timer buzz and lights flicker on and off?

The lower priced dimmers are only rated for 400 Watts. If your switch is controlling more than 400 Watts, then you have a problem--with a potential fire waiting to happen. Add up the wattage of each light bulb you are controlling with the switch to determine if you have less or more than 400 Watts. They do make dimmers rated for up to 1000 Watts. If the problem isn't wattage, I suspect you may be using your dimmer to control a motor (like a ceiling fan motor). If this is the case, you have the wrong kind of switch: one designed for lighting, not motors. They do make dimmers designed for motors; they don't buzz when you dial them down.
2/4/2015 1:29:15 AM • Leviton... • Answered on Feb 04, 2015
Not finding what you are looking for?
Leviton  Decora Light Dimmer Switch Logo

69 questions posted

Ask a Question

Usually answered in minutes!

Top Leviton Electrical Supplies Experts

jdthefixer

Level 3 Expert

747 Answers

john h

Level 3 Expert

24971 Answers

Mike

Level 3 Expert

4377 Answers

Are you a Leviton Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Leviton Electrical Supplies

  • Leviton Electrical Supplies

Most Popular Question

new leviton lighted decorative switch

  • Electrical Supplies
Loading...