The issue of the Paloma tankless water heater displaying error code C7 38 may be caused by several factors, including a problem with the thermistor or temperature sensor, an issue with the gas valve or gas pressure, or a malfunction with the control unit or circuit board. To troubleshoot, try checking the thermistor and temperature sensor, and verifying the proper functioning of the gas valve and gas pressure. If the problem persists, consider seeking professional repair or service.
You can reset the code by turning Gage all the way up highest setting count to ten turn it to hot could to ten then turn to pilot count to ten and then turn it to desired temp burner should come on. Saves lots of money and time
The circuit is about to overload and the break could turn off due from too much electricity being used.The circuit is overloading or there is a problem with the panel needs to be replaced or the wires for your heater could be frayed or have tears in them and need to be replaced.
I've ended up with a Drayton Tempus 3 when I bought my house, and I think this is how it works. It allows you to set 2 Timers (I'll call them timer 1 and timer 2) so that you can control Hot Water or Heating On/Off times twice a day. The unit has 6 buttons - 2 for Adjustment, 2 for Hot Water and 2 for Heating. The 2 Adjustment buttons allow you adjust the Clock Time, or allow you to adjust Timer 1 and/or Timer 2. NOTE: Timer 1 is the time refered to on the Heating / Hot Water Select buttons if you press "Once". If you select "Twice" on these the both Timer 1 and Timer 2 are taken into account. For example if you want Hot Water to come on Once between 8pm -10pm, but you want Heating to come on Twice between 6am - 7am, and 8pm -10pm, you have to do the following: Set Timer 1 to 8pm - 10pm, and set Timer 2 to 6am -7pm. Then select Once for Hot Water, and select Twice for Heating. Hope this helps.
Hi. Very cool requirement you actually have. There is nothing that the experts at this plumbing site in Canada can't do . They have been providing friendly service to commercial customers in Canada for over 20 years. I hope you find my recommendation helpful.
'make model (what it is)' in all question please Rick.
All of the gas passageways in a fridge are very small. If you removed the gas valve and associated pipes, it takes a long time for the gas to bleed through and get from the gas line to the pilot light and that is needed to heat the thermocouple and allow the gas valve to open.
It should also be mentioned that all work on Gas appliances should be undertaken by a qualified and registered gas technician.
Question edited for funky spelling of 'pilot', (piolt light)..You posted to the Cars and Trucks category, what year make and model is it? :>DThis sounds like some type of gas appliance, stove, fire or central heating furnace? It is gas and can only be worked on by a registered gas service technician.'make model (what is is)' in all question of this type please.'year make model' in all vehicle questions please.
It would be. The flue and the cover needs to be attached to reduce air flow and direct it up the flue. Or the pilot light needs the flame turning down. It is a gas appliance and needs to be serviced by a gas certified engineer.Owner manual and technical instructions.https://www.freeboilermanuals.com/assets/pdf/Morco/D61B-good.pdf..
https://mans.io > Rheem > Tankless Electric Water Heaters
Rheem RETEX-27 Performance 27 kw Self-Modulating 5.27 GPM Tankless Electric Water Heater download pdf instruction manual and user guide.
But this says it does, or may have?
Where Is the Reset Button on a Rheem Hot Water Heater? On Rheem water heaters, the reset button is usually a red button located near the thermostat, at the middle of the limit switch. To access it, you will need to remove the metal panel on the unit. The red button is behind the insulation.
Some combi boilers have a 'Keep Warm' function. Check to see if your combi has this feature. This is a function where the system preheats an amount of hot water to provide instant hot water when you turn on the tap/faucet. To do this the combi will start up when it detects the stored water is below a certain temperature to reheat it ready for use. This can be turned off if you prefer not to use it.
