20 Most Recent Kohler K-3386-0 Rialto one-piece round-front toilet with seat and left-hand - Page 2 Questions & Answers

Take lid off and check that the fill tube is in place. If so flush with lid off to see were the water is squirting from, be prepared to clean up water...If you can, do a slight flush. If there is water coming from any where but the bottom of fill valve and the fill tube you may need to replace the fill valve. In my experience, the fill tube is dissconected.

For Diagram
http://www.askmehelpdesk.com/attachments/plumbing/19906d1242687133-shut-off-valve-under-toilet-doesnt-work-fluidmaster-20ballcock.gif

. Check out this link for a few troubleshooting ideas.
http://www.askthebuilder.com/B332_Toilet_Repair_Instructions_for_10_Common_Problems_.shtml

The flush seal is the rubber gasket between the tank and the bowl. You do not have one. So I am guessing you mean the wax ring on the floor?? They usually only get replaced when the toilet is changed, unless you spring a leak. Or are you talking about the flapper inside the tank that holds the water till the flush lever is pulled? Get a new flapper, if it is just the flapper you need, otherwise you will have to buy the whole thing, all these parts are available at the hardware store. I think it is held on by a couple screws in there, might just be a press fit, we don't see too many one piece toilets. And the wax ring is about $2, but the toilet has to be unbolted from the floor and water disconnected, clean off the old wax, put on the new ring, smoosh it back down and bolt it back it up. Don't for get the water line. Check to make sure you have no leaks. Hope this helps.

There is clips where the bolts should be .Flip the clips up grab hold of the seat and pull it strait out towards the front of the toilet.

If you are talking about the seat...Hinge caps snap open to release and the seat pulls forward to remove.

cut the head off from top use a dremel ,wizard or drill with a cut off wheel or sawsall use very carefully and support nut so it doesnt rattle and crack porcelain

There is either a screw on the top of the fluidmaster, or the float can be screwed out further. If it has a screw on top of the fluidmaster, screw it in to make the valve shut off earlier. Keep adjusting and flushing until it shuts off before it overflows. Hope this helps...

break away pieces of the seat and cut from above. I've done it and it is a pain, but works.

Okay. The question is a bit lacking in details. Password for what? Password ON what? Where was the file stolen from? Who stole the file? What is the file content. What is the file extension (the bit after the file name and the period file_name.what)? All questions need to start 'make model (what it is)' first 3 words. And then a clear question. For the 13 people that have tagged this 10 year old question, it is better to post your own question. ..

I have never heard of a toilet that needs an electronic reset, but it appears it is as simple as just disconnecting the power for 10 minutes. It does sound though are yours has a failing flush valve. I managed an airport lounge and we had dozens of electronic toilets and we had to keep a box of spares for them and just put new parts in them including complete control boards. We also kept a box of batteries. https://www.google.com/search?q=kohler+hatbox+toilet+factory+reset ..

Lift and pull the lid forward lift up and disconnect the lift lever from the chain.

https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1095641_2.pdf

I would take it back for another toilet.

Kohler has good support. You can view the diagrams for that unit with the link I am posting. There are no filters listed in the diagram that might need to be cleaned. There is a chance that the unit has developed a clog from hair etc in the pump impellor. The flange may have come loose and is allowing air in the suction side of the pump too. Kohler has online chat and support numbers you can call too. K-1357-RA ' Devonshire 5-Foot Whirlpool with Apron and Right Drain ' KOHLER

just turn the water valve down some

Rent a multimeter and test your connections. As well as checking the breaker

We had a problem with phantom flushing. Call Kholer. They will send redesigned battery holder and top of flush unit for free. Seems to have fixed the issue.

The only batteries are in the docking station. If the remote is attached to the docking station, take that off and set it aside. Next, carefully lift the docking station up and out from the mounting bracket. Look at the back of the docking station, push the two tabs outwards (away from each other) simultaneously to open the battery compartment cover. Replace the batteries (4 AAs) in the correct orientation. Reinstall the cover. Then replace the docking station on the mounting bracket and put the remote back on the dock if desired. These directions are shown in the Homeowner's Guide (without the service parts) available on the product page: https://www.us.kohler.com/us/veil-intelligent-comfort-height-skirted-one-piece-elongated-dual-flush-toilet/productDetail/toilets/1120267.htm . Scroll down to the Installation section to find the link to the document. The current link to this guide is https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1226974_5.pdf . I hope this helps. Cindy Wells

https://www.us.kohler.com/us/catalog/maintenanceLanding.jsp