20 Most Recent
Oster Golden A5 2-Speed Universal Motor Clipper 78005-140 - Page 5 Questions & Answers
Oster A5 clippers wont run
remove the gearbox cover (nameplate) make sur the worm gear from the armature is spinning when switched on, if not turn off there is an internal problem. if it does move then check the condition of the gear it may have some teeth missing.
Oster Classic clipper
check the thrust plate at the end of the armature inside the gearbox any sign of wear replace, take the gear and lever out and test to see if the noise is still there if it is it could be either a faulty bearing or a faulty armature (armatures can run out of balance) all clipper repair parts for the oster are at
www.angliaclipperservices.com .
Blades on razor are not
Disconnect the blade and ensure the drive Lever is moving if it is apply pressure to the lever and make sure it still moves.
There could be a problem with the Gear Wheel inside the gearbox, check for strpped teeth or even a loose post holding the gear and drive lever into place, relavent clipper repair parts can be found at
www.angliaclipperservices.com .
Cutting blade doesn't move
could be the spring is faulty on thie hinge assembly or the tip of the latch has brocken off not securing the blades to the clipper, either way check to see if the blade will disconnect from the clipper without depressing the latch. related clipper parts can be found at
www.angliaclipperservices.com
Oster clippers blade
John! No Problem!
First put the bigger of the two blades witht the size/number facing down, put the cutter on top. (with the side with the flat side of the teeth facing down) Then put the tongue guide inside the tension spring, make sure the tension spring rail is on the tension rail and place them on top of the cutter. To see which bits these are go to:
http://www.sheareaseltd.com/clipper-blade-sharpening/clipper-blades-the-parts
This picture whows the front and back, it differs slightly from your blade, but its same meat different gravy!
Hold all this together with your finger and thumb, flip it over and scre the whole lot together!
www.sheareaseltd.com
Blades fell off oster dog clippers but can't fit
With the hinge of the clipper facing you:
Make sure hinge is open, if it is not, prize it open with a flat head screwdriver.
Slide the blade on with the blade siz/number faceing you.
Snap shut.
If this fails, try again, but push the latch in as you snap them shut.
If this fails, you may need repair!
www.sheareaseltd.com
Cleaning Oster 78004-011 Clippers and blades
OK compressed air is perfect for your clipper, thats all it needs! Take the filters off (at the bottome of the clipper, either side of the cable) periodically and clear from excess fur. Replace. As far as the blades are concerened, Brush the excess furr off with a toothbrush or similar. Slide the cutter (smaller of the 2 blades) to one side (past half way but not all the way off!) clean exposed teeth on both blades with a bit of oil and a toothbrush, push the cutter the other way and repeat. Blade wash's tend to rust the blades, you need a big pot of WD-40. Get a 5 litre tub from the internet, only thing is there, postage will be a killer. I work for a clipper repair, blade sharpening company and we have it delivered by the truckload! Do what you do with the blade wash, but do it in WD-40. Wipe off excess afterwards and dont soak the clipper in any liquid because of electrc shock.
Thats all you can do! When your blades go blunt or clipper needs service repair:
www.sheareaseltd.com If I have helped you please tell your friends about our website! Thank you!
Dura Edge 10W, 2.4mm blade for Oster Universal Motor Clipper
No problem! Dura Edge is just a fancy name! You can get an Oster or wahl, moser. I work with these every day of my life! Either way, they all fit and work. I work for Shear Ease Ltd. Go to
www.sheareaseltd.com they dont have the price for that one on the website but phone them and Colin will give you a price for one and they'll send it out same day.
I have an Oster A5 2-speed. I took it in to have
It is just part of how Oster clippers are. You can try to alternate blades, and spray them with Kool Lube, but they just get warm.
In the event that you would like to sell them or be rid of them, I use their parts to try and fix low income housing clippers.
Clippers will not cut my golden retrievers fur
have you had the blades sharpened by a professional company, you should be able to get around 25 cuts per blade if correctly sharpened. If you have what about the clippers try replacing the Lever which is located at the drive end and goes from side to side.
Not finding what you are looking for?