Kohler 1014-H2-96 Portrait 5' Whirlpool Bath Tub Finish: Biscuit - Answered Questions & Fixed issues


those parts made by unimax as you have found out are no longer made. solution is to put a new pump and control in.

Kohler... | Answered on Oct 08, 2013 | 734 views


There are no filters on jetted bathtubs. There is a screen with dozens of holes located in the footwell of the tub. that is the suction cover. the water flows through that screen into the front of the pump and then out through each of the water jets.

US Parts Center

Kohler... | Answered on Sep 04, 2013 | 181 views


Most Kohler tubs have a water sensor or water level sensor. Is this an air bath tub (holes in the floor)? or a jetted tub? If it is an air bath, the tub will purge after using it 15 to 30 minutes ater it is drained. If it is programable it will come on every 24 hours if it has been programmed. If it is a jetted tub, there may have been water on the sensor and caused it to start up. If it is a single on/off button the switch could have gotten water and caused it to start up, or there is a problem with the control box. It usually will not start a fire if it comes on, most of the newer pumps have run dry seals. If you leave the house for vacation or weekends, I would advise unplugging the tub or turning off the breaker.

Kohler... | Answered on Dec 16, 2012 | 1,407 views


Those controls have not been made for quite a few years now. you will have to come up with your own new finish for that trim.

Kohler... | Answered on Jan 17, 2011 | 95 views


It is called the suction intake- the pump sucks the water in through the suction intake. It serves as a hair and particle trap (safety device). Some suction intakes can be unscrewed counter-clockwise, others have a round cover that can be popped off with a flathead screwdriver (the cover conceals a philips head screw).

[email protected]

Kohler... | Answered on Dec 17, 2009 | 525 views


a good electrican will check for power but may not be able to test a printed control board. Maybe simpler to get a spa repairman

Kohler... | Answered on Aug 13, 2009 | 359 views


you any thing that can fit the surface of the stopper and provide a good suction

Kohler... | Answered on Jun 05, 2009 | 381 views


You have a bad capacitor its located on the top of the electric pump motor. Be sure to turn off the power before attempting to replace it.

Kohler... | Answered on Oct 24, 2009 | 511 views


THEN DO NOT TURN IT VALVES OPEN SO FAR .THINK

Kohler Home | Answered on Mar 25, 2020 | 76 views


Contact Kohler service department for a free replacement

Bidets ' Bathroom ' KOHLER

www.us.kohler.com > browse > bathroom-bidets
Browse KOHLER bidets. Designed to complement the styles of KOHLER toilets and faucets. ... Puretide™ Quiet-Close™ Elongated manual bidet toilet seat.

Intelligent Toilets and Cleansing Seats ' Bathroom ' KOHLER

www.us.kohler.com > article > CNT121600001
KOHLER intelligent toilets sense your approach, open automatically and close and flush when you leave. Or a heated seat that nestles you in luxurious warmth?

Kohler Home | Answered on Feb 20, 2020 | 99 views


We had a problem with phantom flushing. Call Kholer. They will send redesigned battery holder and top of flush unit for free. Seems to have fixed the issue.

Kohler Home | Answered on Jan 09, 2020 | 13,529 views


The only batteries are in the docking station. If the remote is attached to the docking station, take that off and set it aside. Next, carefully lift the docking station up and out from the mounting bracket. Look at the back of the docking station, push the two tabs outwards (away from each other) simultaneously to open the battery compartment cover. Replace the batteries (4 AAs) in the correct orientation. Reinstall the cover. Then replace the docking station on the mounting bracket and put the remote back on the dock if desired.

These directions are shown in the Homeowner's Guide (without the service parts) available on the product page: https://www.us.kohler.com/us/veil-intelligent-comfort-height-skirted-one-piece-elongated-dual-flush-toilet/productDetail/toilets/1120267.htm . Scroll down to the Installation section to find the link to the document. The current link to this guide is https://www.us.kohler.com/webassets/kpna/catalog/pdf/en/1226974_5.pdf .

I hope this helps.

Cindy Wells

Kohler Home | Answered on Jan 05, 2020 | 136 views


Request the parts list from Kohler.

Kohler Home | Answered on Dec 08, 2019 | 102 views


First, identify the style of your quick connect hose.

See the steps on this Kohler Fawcet Link for disconnecting your pull-out kitchen faucet quick connect hose. Follow this link: https://support.kohler.com/hc/en-us/articles/360001798834-Disconnect-Quick-Connect-Pull-Out-Kitchen-Faucet-Hoses

Make sure the water valves are closed and the water pressure is relieved before attempting to service your kitchen taps.

Kohler Home | Answered on Oct 12, 2019 | 2,178 views


I just posted an answer here, but don't see it. ??

Kohler Home | Answered on May 12, 2019 | 141 views


The brand of toilet doesn't matter. You need a product that cuts calcium and lime. It may take some soaking and scrubbing. Once you get it clean, use the product regularly.

CLR makes a line of products:
https://clrbrands.com/en-US/Products/CLR-Household/CLR-Calcium-Lime-Rust-Remover

Kohler Home | Answered on May 10, 2019 | 133 views

Not finding what you are looking for?
Kohler 1014-H2-96 Portrait 5' Whirlpool Bath Tub Finish: Biscuit Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top Kohler Home Experts

john h

Level 3 Expert

23424 Answers

Bill Johnson

Level 2 Expert

306 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Kohler Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...