Jacuzzi Amiga, Soaking Bathtub with Integral Skirt - T715 - Answered Questions & Fixed issues

Study positioning of remaining clip and emulate with the one that fell off. If something broke then you may have to do a Rube Goldberg - a good epoxy might just do the job.

Sounds like you may not have a ground on the motor of the pump or a grounded outlet?
check the wiring on the motor on the cord to make sure there are no wires improperly attached inside the motor housing.

should be able to either push down or up on skirt..has clips that hold it together bottom or top>>are longer shorter to allow movement

Use a rubber stopper measure diameter of hole 1 inch,,,1 1/4 inch,,,???

turn the temperature up on the topside panel. if it is wired 220v then it will get to 104 deg in about 3 hrs

Go on searc and enter the manfasturer, model and manual. see what pops up.

Thermostat calibration is suspect

You should be getting error messages like flo or FLO2. check the voltage to the pump from the board if power is there the pump is bad and needs replacing

You will have to contact the manufacturer for a service manual for your unit. Do you have an access panel. Usually the apron can be removed for easy access. Also, on some units the trim around the switch can be screwed off and the tubing accessed that way.

The flashing on/off light in a Jacuzzi whirlpool bath may indicate an issue with the control system, and it's important to address the problem to ensure the proper functioning and safety of the whirlpool bath. Here are some general steps you can take to troubleshoot the issue: 1. Check the Power Supply: - Ensure that the whirlpool bath is receiving power. Verify that the circuit breaker for the whirlpool bath is not tripped, and check for any loose or disconnected power cords. 2. Inspect the Control Panel: - Examine the control panel for any visible issues, such as loose or damaged wires, connectors, or buttons. Ensure that there is no water or moisture present in the control panel area. 3. Reset the System: - Some whirlpool baths have a reset function. Turn off the power to the unit, wait for a few minutes, and then turn it back on. This can sometimes reset the control system. 4. Refer to the User Manual: - Check the user manual that came with your Jacuzzi whirlpool bath for specific information on troubleshooting and resetting the control system. The manual may provide insights into the meaning of the flashing light and how to address it. 5. Contact Jacuzzi Customer Support: - If the issue persists and you cannot find a resolution through the manual, contact Jacuzzi customer support or the manufacturer for assistance. They may be able to provide guidance on how to troubleshoot and resolve the issue. 6. Professional Inspection: - If you're not comfortable or able to identify and fix the issue, it's advisable to seek assistance from a qualified professional or a technician experienced in Jacuzzi whirlpool bath systems. They can perform a thorough inspection and diagnose and repair any electrical or control system problems. It's essential to prioritize safety and follow proper procedures when dealing with electrical components and water. If you're uncertain or if the troubleshooting steps don't resolve the issue, it's best to seek professional assistance to avoid potential hazards.

they twist out

Maybe these folks can help they stock allot of Jacuzzi parts.

Can't Find It?

Send us a picture Text a photo: 305-321-3420 https://www.guillens.com/catalog/shop/Jacuzzi/Bath/Repair-Parts/Control-Boxes/mfr-3BU?pagenum=1

yes the are and parts are available on line.

Hi, Please attempt to start the jacuzzi without any water and see if it functions. Then you can fill the jacuzzi up to 1/4th with water and check if it continues to run. If so, continue to one half full. If this jacuzzi breaks down at these water levels, then you'd need to call the manufacturer to advise on what part needs to be changed to get everything working again. Thank you.

No, replace the whole thing. That is bad design and inferior parts. Ask Moen to replace it under warranty. They might say No, but then again, they might know of a fix or if they had a bad batch of plastic parts.

Hello, Several things can cause this problem- if you post a picture of the inside of the tank so we can have a good look at how the fill/stop mechanism operates that would be great. We could more than likely identify some type of problem and solution. Not all flush/fill mechanisms are not the same but thats surely where your problem is UNLESS its in your water lines. I would love to help you just please provide photos and as much information as you can. Good luck! Mr.Mike

pump -impeller failure /bearings /motor failure

Contact the Dealer and seek qualified tech service. Risk of electric shock/***** You should not take the risk but have a QUALIFIED SERVICEPERSON perform the work.

There may be a video but you should be able to tell by looking at it too big screw under tank holds valve on big screw under tank holds valve on see: https://reviewmotors.co/jacuzzi-dual-flush-toilet-repair-parts

If there is power to the unit, most likely it will need to be replaced. Check for reset button, and check the fuses before replacing the unit.