American Standard 2770.018w.020 Cadet Whirlpool White - Page 9 - Answered Questions & Fixed issues
I need drivers for motorola router sb5100
I hope you get this... it's posted in the bath section!
An easy answer... Download the drivers here:
http://broadband.motorola.com/consumers/support/default.asp?supportSection=DiscontinuedProducts
9/13/2010 6:24:05 AM •
American...
•
Answered
on Sep 13, 2010
•
51 views
Does a bathroom require an exhaust fan even if it
YES!!!! all a window does is change the vapor into liquid. What is needed is to get the moisture OUT OF THE building. I prefer Neutone 200 CFM unit, for get specs, they are all way too low. You are combating health issues if you allow moisture to remain....mold...
Also, the exhaust ducting needs to run downhill as it exits the building, or you risk moisture dripping from the fan...
Futher, put a 60 minute timer on the fan, and run 45 minutes (at least) for every shower....
9/5/2010 6:30:29 PM •
American...
•
Answered
on Sep 05, 2010
•
256 views
Very slow drainage of a small bathroom sink.
probably hair stuck in the drain. did you remove the stopper "pop up" if no hair or blockage there or in the trap, then its further down, you will need a small snake. 1/4 inch cable works well in bath and kitchen drains.
you can purchase one at home depot.
7/1/2013 3:36:59 PM •
American...
•
Answered
on Jul 01, 2013
•
414 views
When flushing, water does not go down completely.
you can get universal replacement parts from your local hardware or plumbing supply store. For some models you may have to remove the tank from the bowl. Most you can unscrew from inside the tank without removing. Good luck.
8/3/2010 3:43:20 AM •
American...
•
Answered
on Aug 03, 2010
•
122 views
My one piece original porcelain sink and counter
If it is truly a porcelin top then you can use a product called plumbers putty available at your local hardware store. It will conform to the shape of the drain and provide a good seal. If this is a cast marble or resin type of product then plumbers putty will void any warranty and possibly discolor the sink. Ensure it is indeed porcelin before continuing and follow the manufacturers directions for installation. Good luck with your project.
7/16/2010 4:01:53 AM •
American...
•
Answered
on Jul 16, 2010
•
260 views
Toilet bowl doesn't hold water but tank is full
The bowl is filled up with the little hose inside the tank, it locks inside of the overflow drain. And runs water in there as it flushes to swirl the water and fill the bowl. Water seeks it's own level, and the level in the bowl is at the top of the trap. It has to hold water, unless it isn't filling or it is leaking. Check out the filler and hope the bowl doesn't have a crack in it. Hope this helps.
5/3/2010 11:00:09 PM •
American...
•
Answered
on May 03, 2010
•
336 views
Hi,I have a Bathtub Shower Valve that is not working
SHUT OFF THE WATER SUPPLY VALVE BEHIND THE SHOWER.THOSE HANDLES ARE DIFFICULT TO REMOVE,SQUIRT WD-40,LET IT SOAK IN,THEN GIVE IT A LITTLE TAP ON THE HANDLE ,BE CAREFUL NOT TO DAMAGE IT.IF YOU CAN NOT STILL REMOVE THE HANDLE,THEY SELL A HANDLE PULLER,
4/21/2010 4:13:33 PM •
American...
•
Answered
on Apr 21, 2010
•
413 views
I have an American Stadard Toilet that is only 2
There's a lot of variety in the works in the toilet tank. Assuming this is not a pressure-assisted toilet-----First understand the three valves are:
1. The shutoff valve - on the supply line coming into the toilet tank.
2. The fill valve - inside the tank, opens with the float descends, closes when the tank fills up.
3. The flush valve - inside the tank on the bottom. Common old style is a flapper on a pivot. Yours may operate straight up and down rather than on a pivot.
Three very common problems are----
1. The chain that connects the handle to lift the flush valve is getting caught, not allowing the flush valve to close.
2. There is problem with the flush valve being able to get a good seal when it closes - could be debris or misalignment.
3. The fill valve is not closing when the tank is full, could need adjustment or there is debris preventing the valve to seat.
.
Here's are some steps to diagnose---- close the shutoff valve. Wait a few minutes as you watch the level in the tank. If the water level decreases, you have problem with the flush valve.
To confirm the fill valve as the problem, turn the shutoff valve back on. Lift up on the float that is supposed to turn off the fill valve. If it shuts off, you should be able to adjust it - most have a +/- plastic adjustment screw. But if raising the float by hand only slows it down, you have problem with the seating of the fill valve - which can sometimes be cleaned, but more often would need to be replaced.
I hope this is helpful. Thanks for using FixYa.
4/2/2010 2:13:56 PM •
American...
•
Answered
on Apr 02, 2010
•
396 views
How to remove jet rings on jetted tub
It depends on the brand of jet and tub, if it is a gold or silver trim ring, they will generally pry off with a screwdriver, just be careful not to damage the tub when doing so. When prying, move the screwdriver around the jet an inch at a time, just like opening a can of paint. Some rings will screw on, but most just pry off.
3/25/2010 11:31:02 PM •
American...
•
Answered
on Mar 25, 2010
•
3,014 views
Broken jet line
If the break is in the flexible tubing that connects the nozzles it is most likely spa-flex. This is the same size as nominal schedule 40 pvc and can be repaired with standard pvc fittings, primer and glue. Make sure the surfaces are clean and dry before repairing them and also allow at least 24 hours cure time on the glue.
3/23/2010 4:05:55 AM •
American...
•
Answered
on Mar 23, 2010
•
76 views
When jacuzzi is on water turns yellow
Are you on well water? If so you may have dissolved iron in the well water, it enters your house as clear water iron and then once areated in the tub it turns yellow as the iron oxidizes. Another sure sign of this is if the water in your toilet yellows after sitting in the bowel with no use after a few days. Solution: have a reputable local water treatment company come test your water, test for disolved iron, total hardness, and pH. If the disolved iron is 5ppm or less then a water softener will fix the problem. Make sure they add a turbulator to the softener and use iron fighter salt or mix iron-out into the salt tank.
3/23/2010 3:38:48 AM •
American...
•
Answered
on Mar 23, 2010
•
215 views
What is a bath
A method or means of cleansing something or someone.
3/20/2010 9:41:14 PM •
American...
•
Answered
on Mar 20, 2010
•
133 views
Where can i get an Air switch 6871-aeo-u626
I assume that number is off the old switch. It is next to impossible to locate parts such as an air switch that way. What you generally need to know is what size the orriface is to fit the tubing, if it is a double or single pole switch, how it mounts in the control, etc. Based on those answers you would purchase a generic replacement.
Try this catalog if you like (**Warning** It is a large file: 20+ MB) and if you can ID the part(s) please contact us thru
www.arrowpools.net for a quote on it.
12/17/2009 9:16:58 PM •
American...
•
Answered
on Dec 17, 2009
•
513 views
Not finding what you are looking for?