Sharp R-1610 Microwave Oven - Page 9 - Answered Questions & Fixed issues


Check microswitches.

Sharp Microwave... | Answered on Sep 27, 2018 | 127 views


You can contact Sharp at 1-800-BE-SHARP (1-800-237-4277) or visit them online.

They can answer this right away.

- William E. Miller, AS-EET
[email protected]
http://www.MicrowaveControl.com
Microwave Oven Control Panel Repair Nationwide

"Recycling by repairing since 1982"

Sharp Microwave... | Answered on Dec 10, 2017 | 100 views


The coupler just slips onto the turntable motor but they can be hard to remove. Try prying from opposite sides of the coupler but be careful not to damage the area around the coupler.

Sharp Microwave... | Answered on Nov 10, 2017 | 39 views


Sounds like a broken touch panel. Many of the pads are connected in a line and if a trace breaks you lose all the pads ran on that common trace. Are you looking to repair this your self? If not, you will need to find someone who services sharp or carries parts for them in your area

Sharp Microwave... | Answered on Oct 16, 2017 | 74 views


Changing the light bulb on your Sharp carousel microwave will allow you to have needed light inside the oven. Microwaves are not designed for consumers to change the light bulb due to manufacturer liability, but it can be done. Following the proper steps will ensure a successful installation. Step 1 Unplug the Sharp carousel microwave from the electrical outlet.
Step 2 Locate the screws around the outer cover of the Sharp carousel microwave and unscrew all the screws.
Step 3 Lift off the covering.
Step 4 Locate the bulb and unscrew. Screw in your new bulb.
Step 5 Replace the cover and screw back tightly. Once done, test your new bulb.

Sharp Microwave... | Answered on Oct 10, 2017 | 627 views


Before you invest too much time, look and see if the touch pad is still available. Sharp is pretty quick to discontinue parts right after about 5 years. There is a place called encompass parts. They are a distributer for Sharp, you micght check with them.

Sharp Microwave... | Answered on Oct 09, 2017 | 88 views


Un plug for a few minutes, plug back in, set the clock ( time of day) try again.

Sharp Microwave... | Answered on Oct 04, 2017 | 85 views


check the relays on the PCB, don't do it on the board but remove them outside and check properly.

Sharp Microwave... | Answered on Sep 22, 2017 | 648 views


Timer section is fubar. Reset the electronics to factory defaults and see if that cures the issue. If not, the timer section needs to be replaced.

Sharp Microwave... | Answered on Sep 22, 2017 | 66 views


You need to know why the fuse blew first. two places that will cause the fuse to blow is excessive current being drawn from a shorted winding in the transformer or a bad magnetron unit. If the holder is loose, pinch the metal parts that contact the end of the fuse slightly to restore proper contact with the fuse.

Sharp Microwave... | Answered on Sep 16, 2017 | 235 views


On/off circuit is bogus. Check for a frozen switch in the on position.

Sharp Microwave... | Answered on Sep 12, 2017 | 151 views


Call the manufacturer about resetting the electronics. If not possible the board needs to be replaced if the price is right.
check here Search Over 2 1 Million Appliance Parts

Sharp Microwave... | Answered on Sep 08, 2017 | 83 views


If it is still under guarantee and you have the receipt take it back to the supplier.

Sharp Microwave... | Answered on Sep 02, 2017 | 38 views


How do you know how much electricity it is using??? Is it actually working and heating as it should??

Sharp Microwave... | Answered on Aug 24, 2017 | 43 views


I believe you mean wave guide cover. Are you talking about a silver looking square or rectangle cover, typically held in place with 1-2 screws?? If so that is a wave guide cover. You must keep them clean and dry. Clean off any food splatter promptly and clean with a damp scrubby sponge. do not saturate. Try to keep dry. Sharp's distributor is a company called Encompass parts. you would need your model number.
https://encompass.com/

Sharp Microwave... | Answered on Aug 24, 2017 | 32 views


Also the fact it is a convection oven could mean the oven temperature sensor is not picking up the oven temp. it is not telling the machine it is there by the board seeing its resistance, the unit will shut off as a safety feature. The oven sees temperature by reading the value of a temperature dependent resistor. As the temperature changes so does the value of the component ( oven temp sensor) that way the unit determines the temperature inside the unit. Sometimes those sensors will break since they are in the area with the heat and moisture, they get old and break.

Sharp Microwave... | Answered on Aug 18, 2017 | 139 views


I am not positive about this specific model but on a good amount of the Sharps I have worked on in the past they typicall have long screws that go from the top front of the units to the back of the unit where they screw into the plate mounted to the wall. If you remove the plastic vent along the top front of the unit above the door a lot of the time you will find screws there that you loosen to lay the machine toward you and then you have to lift it off of the bracket and take it out. Good Luck

Sharp Microwave... | Answered on Aug 16, 2017 | 276 views


First of all, Do you have it on a level surface?

Sharp Microwave... | Answered on Jun 30, 2017 | 144 views

Not finding what you are looking for?
Sharp R-1610 Microwave Oven Logo

107 questions posted

Ask a Question

Usually answered in minutes!

Top Sharp Microwave Ovens Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Brad Brown

Level 3 Expert

18563 Answers

Are you a Sharp Microwave Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...