Sharp R-1872 Convection/Microwave Oven - Answered Questions & Fixed issues

test the thermal fuse for open or bad contact with VOM2)check the hooks door, or release door button, +switch door for open with VOM.see the diagram for troubleshooting.Gd bless you

There are several possible causes... none of which are user serviceable. Take unit to a shop for repair.

Possible problems include door switch, Magnetron, rectifier, control relay, etc.

Yes, this is a common item. Any appliance store that handles the Sharp line will be able to order the racks for you, if they do not have them in stock.

Did it have the installation instructions? That will list the part numbers you need.

If not, the original part number for the installation instructions was TINSEB371MRR0, which was replaced by TINSEB141MRR0. (both end in zero, not "oh")

You can get the latter via Encompass (formerly Tritronics, the best place to get Sharp parts).

Or you can call them toll-free at 866-779-5835, which will get better results. They should also be able to tell you the parts you'd need to install it.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

Info on ordering Sharp UK parts / spares is here.

We're happy to help you with free advice and we'd appreciate your thoughtful rating of our answer.

I have this model. Press clear then press Auto/Clock. Enter in the time eg 700 then press Auto/Clock again. The time should now be set

It is a motorized drawer and I doubt it likes being opened manually. It would need to be repaired professionally due to the inherent dangers of microwave energy. The drawer motor would be operated by a relay. Did you read any reviews before you purchased it? IanFromOhio a year ago Thumbs Down - Looks great but features are bad. Drawer microwaves and this model in particular look great. We did a big reno in December and this is now in the island. Looks good and functions as a basic microwave. Everything else is just south of mediocre. I'd suggest you get a drawer microwave from another company. Bad Stuff: - door opens/closes very slowly (~4 seconds)... doing a 30 second reheat now takes 4+4+30+4+4 = 50% longer just standing around. Likely similar with other drawers, but an unexpected negative. - doesn't let you tell it to start until fully closed - its default sounds and reminders are ridiculously annoying - beep-beep-beep on finish, and 10 seconds after that, and 10 seconds after that, and.... on and on - it forgets all settings during a power outage, turning back on the annoying sounds - and forgets your network connection - but good news, you won't want to use that feature - controls are not intuitive - classic 40 buttons where you use 5 The WiFi & App - hilariously bad. Design in your head the things you would want in a microwave app. Sharp engineers designed the opposite. Can you set the alarm settings in the app? No. Do you get a notification each time the microwave finishes cooking? Yes. I guarantee you will delete the app within 48 hours. Hand Wave to open. Neat right? No. Take how long it takes for this thing to open/close and add another 4-8 seconds of waving your hands (which are full food, else you'd just press the button) to then wait for the drawer to open. Push to close works well, but it reacts in a weird way, so some concern I'm breaking it. I stopped doing wave to open after the first week and stopped trying to demonstrate it to friends after one month (cause it will make you look silly). Height - just tall enough - fits a Venti coffee Cooks at 950 watts - basically the same power as a college-dorm microwave Cost. my god, how much did I spend on this. The good: Looks good Flush install if you have a good installer; mine is shown in a 30" wide lower microwave cabinet by Medallion Reheat sensor cook works well push to close works. It was suggested that I buy a Sharp because they have the patent on the drawer microwave and everyone else is just a re-labelled Sharp. I would suggest you give the others a look. They may be using the same hardware, but hopefully they have a more customer-focused interface and better software engineers working for them. Reviewed on bestbuy.com

The E-03 error on a Sharp CD-C492 CD player typically indicates a problem with the door or the mechanism that opens and closes the door. Here are a few steps you can try to fix the issue:

1. Check for foreign objects: Make sure that there are no foreign objects blocking the door or preventing it from opening.
2. Check the door hinges: Inspect the hinges on the door to ensure that they are not damaged or stuck. If the hinges are damaged or stuck, try gently wiggling them to see if this helps free them up.
3. Check the door switch: Locate the door switch, which is usually located near the hinges on the door. Check to make sure that the switch is functioning properly and that it is not stuck or damaged.
4. Check the door motor: If the door switch and hinges are functioning properly, the problem may be with the door motor. Check to make sure that the motor is functioning properly and that it is not damaged.

If you are unable to fix the issue using the steps above, or if the error persists, it is recommended to have a qualified technician take a look at the CD player to diagnose and repair the problem

DO NOT use this oven for any of the functions! You will need to get a specialist to look at this! Smoke suggests a motor or the wiring to it is burning out. Is this a free standing unit or a built in setup? Free standing unit or often not too expensive to replace and there are lots of Companies who make good upgrade models. Get quotes for the repairs from 3 or 4 different places and compare that to the cost of a replacement.

Hi, please call sharp over the phone and ask them to email the manual to you so that you can receive the document without paying any shipping fees. If you need to print it out and it has many pages, you can do so at your local office depot or kinkos. Than you.

They are here https://www.repairclinic.com/Shop-For-Parts/a6c19i240/New/Microwave-Fastener-Rivet-Parts https://www.google.com/search?q=Waveguide+plastic+rivets+for+Sharp+R-651zs ..

My drawer has been sticking for years and always required a little force to get it to open. Just fixed it by putting a little silicone grease on the drawer hooks that are exposed when the drawer is open

In case of unavailability of touch panel regarding any model of your microwave you can simply asked your repairman to install micro touch buttons (easily available and can be fixed) on the base of touch panel than repest the panel over it. It would work like the same.

I searched using https://www.google.com but did not locate an instruction manual for that model Sharp microwave oven. Recipe at the link below suggests adding extra sugar before baking. https://www.allrecipes.com/recipe/140772/easy-microwave-chocolate-cake/?_ga=2.211667349.160497590.1579435247-959462057.1579435247

Okay. I got the Half Pint Microwave door off, opened it up, found the spring, used a Dremel to make a new point of attachment for the spring since the spring flang on the dooor was indeed broken. The door closes now and microwave turns on - but it doesn't stay on, unless I apply pressure on the top right corner of the door. So the latch is just slightly out of alignment. Will tinker with it some more. Maybe it's just a matter bumping up the lower part of the door a bit. Has anyone encountered this problem?

Try here https://www.repairclinic.com/Shop-For-Parts/a6b113/Sharp-Microwave-Parts More here https://www.google.com/search?q=Sharp+wave+guard ..

the LCD is bad, 22 year later a great run that.use flash light to it , see data there that means backlamp deadbuy new one.THERE IS NO LCD FUSE EVER. it used low powerfrom he PCB (display drive logic is there only)the PCB may have fuse or onboard solid state fuse. that self resets if shorts are removed.if you see no fuse there, F1 F2, etc there is none.!use the flash light test. first.. OK??SO DOES OUR POST MEAN , ONLY lcd dead, BUT BOTTONS NOT DEAD and most beep, so beeps dead? see buttons with programmed times, like pop corn etc, do those work?LCD dead sure makes time set hardbut gee, hit time 11 and run,see if 11s seconds, runs the fan and Uwave maggycooks for 11 seconds. blind./lots to test there before giving up.OK only LCD is dead.

Lots of issues with this gimmicky microwave. Call for service, the only thing you can try is a power reset. Reviews are not good which is odd for a brand leader like Sharp. https://www.google.com/search?q=Sharp+KB6524PS+Microwave+Drawer ..

possible bad high limit temp sensor

If it shuts down it is faulty. Take it in for professional repair. They are too dangerous to work on. There is 125,000 volts in the capacitor just waiting for you to get near it. The magnetron will make you blind in about 15 seconds and the core is a poisonous heavy metal. It is a $2,190.00 commercial microwave so worth getting repaired professionally. It must have earned its money. Service Manual, and note: WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may result in a severe, possibly fatal, electrical shock. (High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)

Sharp CD2200M Service manual ' Manualzz

https://manualzz.com > Sharp > microwaves > CD2200M TopPage RCD2200M SERVICE MANUAL S2801RCD22MP COMMERCIAL MICROWAVE OVEN MODELS R-CD1800M R-CD2200M In the interest of user-safety the oven should be