Top 20 Mountain Plumbing Mountain The "Little Gourmet" Heating Tank MT641 Questions & Answers

Replace heater? Why type and brand heater is this? http://waterheatertimer.org/How-to-fix-water-heater.html http://waterheatertimer.org/Leaking-water-heater.html Gene If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Have you tried refilling your radiator looking for an air pocket?

You need the push tool to release the internal spring.

if it is a ribbed fitting then yes

Same problem Leaking unit!... and also saw issues with the thin rubber hose.. other listed that their hose melts!!

Not sure if you are In Uk but Danfoss manufacture these and are available fron The likes of B.S.S.

most of the units have a screen on the inlet that may be plugged

You need a radiator bleed valve key. They are about the size of half a little finger with a 't' bar at one end and a small square socket at the other. made in brass or aluminum
Any DIY shop should have them

No attack on this scale is heating element that dissolves when it is possible to disconnect apperaat water heating and draining than doing it in vinegar and let the heat once again connect and then empty and most calcium is removed from apperaat

check thermostat

It may be a push n lock. If you can send a pic of your phone vam, send one and we can see what's needed. [email protected]. If its a push n lock, While pushing on the line push in the smaller inner sleeve and pull on the line. Make sure there is not pressure in the line.

sounds like you need a new tank my friend! go tankless!

you will have to get a replacement from the manifacture,, they will send it to you, call them tell them wich one it is hot or cold they may have diffrent threads then again they may be the same,,,can you get the threaded part out of the faucet, you will need an extractor, you can get this at a hardware store, it has a rubber seal so you can only tighten it so much, get it ot try again but be gentle,, one thing I found after doing plumbing for 34 years if you snug it and it leaks you can always snug it some more if you over tighten it you can't do anything but replace it,,,, good luck let me know how it goes

this is a condensate line and suprising enough most of the plumbers I go back after never hook them up they should have a hose off of them and led to a discharge area, if this is actually on the tank you will need to drain it and remove it and reseal it,

Make sure that there is no leaks traveling down the hoses or at the connections on the top. The tanks can leak, if you have the Stainless Steel tank the following information applies - Stainless Steel Tank: 3 years, with an extended service plan available when installed by an InSinkErator Pro Circle™ plumber. I you product is under warranty I believe that you can call the number that is printed on the tank and literature.

the temp is to high and it is just a neoprheme hose go to the hard ware store and purchast a new hose the samt size 3/8 re install it and trun the temp down on the unit, make sure the hose you get has at least 140 degree rating

anything can be rebuilt the only problem is wether the rebuild is cost effective time material wise.

HOW IS "HE"? moved you out of computer repair help to water heaters For a real home or mobile home or RV.??????? you meant, this, full number. ES38 (RHFE-1004RFA) 2009 model, (google shows) you failed to say in what country, and they are not the same. by law and the above is for Mobile homes. ask them what is new, and btw the serial number on it will disclose dates. here is the maker, web site USA. just one country (wild guess) https://www.rinnai.us/residential/condensing-boilers

To be sure a camera inspection will show if there is a broken pipe before you start taking up floors .

the float valve that controls the level on water in the tank. is going bad. when they start to go bad the water pressure cause the the valve to flutter (tries to open and close at the same time.