Top 20
HiTi P110S PocketStudio Photo Printer Starter Kit - Page 8 Questions & Answers
How to change empty tray message please?
Question edited for typos.
All questions need full 'make model (what it is)' as the first 3 words.
Remove the tray and look for sensors or something on the paper tray that registers when it is out of paper. Fill the tray and replace it.
Also try a power reset. Remove to wall plug for 10 minutes then plug it back in.
..
Shredder Essentials SES-C1525 Shredder. How do I unjam a ses-c1525 jammed with what I think is sticky gunk.
Question edited for full 'make model (what it is)'.
People don't realize that shredders need oiling regularly. Spray all the blades and the gunk with WD40. Leave it half an hour and spray it again. Run it in reverse to clear the jam. If you have been using it a lot, they have a thermal cut out which should reset after about 20 minutes or so. Bad jams and heat, shatter and shred the gears inside the head. Is the motor making any noise?
TMX15 ERROR CODE 204 is coming up on display. Anybody know what that may be?
TMX15 is a model of a forklift truck, and ERROR CODE 204 indicates a fault with the accelerator pedal position sensor. This sensor is responsible for sending signals to the forklift's engine management system to control the speed of the vehicle.
The error code may have been triggered by a faulty sensor, damaged wiring or connectors, or a malfunction in the engine management system itself. It is recommended to have a certified forklift technician inspect and diagnose the issue to determine the root cause and necessary repairs.
It is important to address this issue promptly, as a malfunctioning accelerator pedal position sensor can affect the performance and safety of the forklift.
Can I put an equals sign on my calculator
Yes, almost all calculators have an equals sign. The equals sign is typically used to indicate the end of an arithmetic operation and to display the result. The location of the equals sign may vary depending on the specific calculator model, but it is usually labeled with the symbol "=" and located in a prominent position on the calculator keypad.
Cl-100 topcon lenso meter initial error problem always comeback when I fix.. pls help how to solve for this
The CL-100 Topcon Lenso meter is a surveying instrument used for measuring distances and angles. An "Initial Error" message can indicate a number of different issues, including:
- Calibration Issues: Check that the instrument has been calibrated properly and the calibration values are within the acceptable range.
- Software Issues: Update the software on the instrument to the latest version, which may resolve any bugs causing the error.
- Hardware Issues: Check the instrument's hardware components, such as the battery, for any signs of damage or wear and replace if necessary.
- Settings Issues: Make sure that the instrument's settings are set correctly and adjust them if needed.
- Environmental Factors: Environmental factors, such as temperature and humidity, can affect the performance of the instrument. Make sure that the instrument is being used within the recommended temperature and humidity range.
If the "Initial Error" message continues to persist, it is recommended that you seek assistance from a qualified Topcon technician or authorized service center. They can diagnose and repair the issue and restore the instrument to full functionality.
Caster holder broken and won't auto-stop after shred
I see you posted two questions on the same issue, and the other one was disjointed with no indication what the caster wheels were on.
Check the switch, they normally have On, Off and Auto.
Remove the head and clean all paper debris from underneath. You have a small piece of paper over the sensor and it is sensing that there is still paper for be shredded. Some have a small lever and if so, yours is stuck. Spray with WD40, and all the blades as well.
https://www.google.com/search?q=Ativa+MDM+8000
The caster wheels could all be removed and have it sitting on its base. The wheels are for use if you keep it in an office cupboard. You just replace the whole caster wheel or the whole set for $14..
https://www.google.com/search?q=Caster+wheel
..
Rexel LV250HS Laminator stopped heating up. Can it be repaired.
Question edited for a lot more clarity which a guess at the maker.
Question moved from Microwave Oven.
It depends. If it is just a broken wire or a faulty switch, probably yes and easily. If the heating element has failed, getting spare might be the hard part. Start with checking the easy stuff with a multimeter.
Kangro HP-45 tray not lifting to create space for papers
If the paper tray on your Kangaro HP-45 stapler is not lifting to create space for papers, it could be due to a few different issues. Here are some steps you can take to fix the problem:
- Check the tray for any paper jams: If there is paper stuck in the tray or in the stapler mechanism, it could be preventing the tray from lifting. Carefully remove any paper or debris that may be obstructing the tray.
- Check the spring: The tray lifting mechanism in the stapler is usually spring-loaded. If the spring is damaged or worn out, the tray may not lift properly. Try replacing the spring with a new one.
- Check the lever: The tray lifting mechanism may be controlled by a lever or other mechanism. Check that the lever is properly aligned and not obstructed by any debris.
- Check the tray guides: The tray guides may be bent or misaligned, preventing the tray from moving smoothly. Try adjusting the guides to ensure that the tray can move freely.
- Check the tray stop: The tray stop may be preventing the tray from lifting. Check that the stop is properly aligned and not obstructed by any debris.
If these steps do not resolve the issue, it may be necessary to take the stapler to a professional repair technician for further diagnosis and repair.
Calculator not feeding paper model TI-5035II
If your TI-5035II calculator is not feeding paper, it is likely that the paper feed roller is not properly connected. Make sure that the paper feed roller is securely connected to the calculator and that the power switch is in the "on" position. If the problem persists, you may need to replace the paper feed roller or contact the manufacturer for assistance.
FDL 9640p uk. Start/pause key flashes every three-four seconds. machine wont start.
The flashing start/pause key on your FDL 9640p machine could indicate an error or a malfunction. Here are a few steps you can try to resolve the issue:
- Check the machine's power source: Make sure the machine is properly plugged in and the power source is functioning.
- Reset the machine: Unplug the machine for a few minutes, then plug it back in and see if it starts.
- Check for clogs: Look for any blockages in the machine's pipes, hoses, or filters that could be preventing it from functioning properly.
- Contact the manufacturer: If the machine still won't start after trying these steps, you may need to contact the manufacturer for further assistance. They may be able to provide more specific troubleshooting advice or arrange for a repair.
If the issue persists, it may be best to seek professional repair services to have the machine fixed.
Lexmark mx611de [88.30] cartridge replacement error, 0 estimated pages remaining
The "88.30 cartridge replacement error" message on a Lexmark MX611de printer indicates that the printer is unable to recognize one or more of the cartridges installed in it. This can be caused by a variety of issues, such as:
- The cartridges are not properly installed in the printer.
- The cartridges are not compatible with the printer.
- The cartridges have reached the end of their useful life and need to be replaced.
- The printer's firmware is out of date and needs to be updated.
To resolve the issue, you should try the following steps:
- Turn off the printer and unplug it from the power outlet.
- Remove the cartridges from the printer and make sure they are properly installed according to the printer's manual.
- Clean the electrical contacts on the cartridges and the printer with a dry, lint-free cloth.
- Reinstall the cartridges in the printer, being careful to align them properly.
- Turn on the printer and check if the error message is cleared.
If the error message persists, you may need to check the compatibility of the cartridges with your printer model and the age of the cartridge. If the cartridge is old, you might need to replace it.
Updating the firmware of the printer can also solve the problem, check the Lexmark website for update on the same.
In case the problem persist after trying all the above troubleshoot, please contact Lexmark support for further assistance.
It turns on and 5 seconds later e4 code pops up
The "E4" error code on a T9200 Vision Fitness treadmill typically indicates a problem with the incline motor. This could be caused by a malfunctioning motor, a problem with the wiring or connections to the motor, or an issue with the incline sensor or control board.
Here are a few things you can try to troubleshoot the problem:
- Check the wiring and connections: Inspect the wiring and connections between the incline motor and the control board to make sure that they are securely connected and not damaged.
- Check the incline sensor: Make sure that the incline sensor is functioning properly and that it is not blocked or damaged.
- Check the control board: Make sure that the control board is functioning properly and that it is not damaged.
- Check the incline motor: Make sure that the incline motor is functioning properly and that it is not damaged.
It's important to follow the instructions carefully and if you have any doubts or difficulties, consult the treadmill's user manual or contact Vision Fitness customer service for assistance. It's also important to note that it is recommended to have a professional technician to perform this task as it may cause other issues if not done properly.
How to hook up my projector
For every projector ever made in the history of projectors?
All questions need full 'make model (what it is)'.
Google
make model manual
..
Not finding what you are looking for?