20 Most Recent
HiTi P110S PocketStudio Photo Printer Starter Kit - Page 2 Questions & Answers
What size staples do I need for the Rapid Isaberg 16 stapler [prob 40/50 years old but still works superbly]
The Rapid Isaberg 16 stapler uses 26/6 size staples. These staples are also commonly referred to as "standard staples" and are widely available at most office supply stores or online retailers. They measure approximately 6mm wide and 11mm in length, and are compatible with a wide range of staplers, including the Rapid Isaberg 16. Be sure to use high-quality staples to ensure that your stapler functions properly and staples securely.
TMX15 ERROR CODE 204 is coming up on display. Anybody know what that may be?
TMX15 is a model of a forklift truck, and ERROR CODE 204 indicates a fault with the accelerator pedal position sensor. This sensor is responsible for sending signals to the forklift's engine management system to control the speed of the vehicle.
The error code may have been triggered by a faulty sensor, damaged wiring or connectors, or a malfunction in the engine management system itself. It is recommended to have a certified forklift technician inspect and diagnose the issue to determine the root cause and necessary repairs.
It is important to address this issue promptly, as a malfunctioning accelerator pedal position sensor can affect the performance and safety of the forklift.
How can I obtain a Robic sc- 8oo el instruction manual?
The Robic sc-800 el is a stopwatch/timer device commonly used in sports and fitness activities. To obtain an instruction manual for the device, you can try the following:
Check the manufacturer's website: The manufacturer of the Robic sc-800 el stopwatch/timer is "Robic" and they may have a website where you can download the instruction manual for free. Go to their website and look for a "Support" or "Downloads" section where you may find the manual.
Contact the manufacturer: If you can't find the manual on their website, you can try contacting the manufacturer directly. They may be able to send you a copy of the manual or provide a download link.
Search online: There are many websites that offer user manuals for various products, including the Robic sc-800 el. Try searching on websites such as ManualsLib or ManualsOnline.
Check with retailers: If you purchased the device from a retailer, you can contact them to see if they have a copy of the manual or can provide a link to it.
Ask for help on forums: There are many online forums and communities dedicated to sports and fitness activities. You can try asking for help on these forums to see if anyone has a copy of the manual or knows where to find one.
I hope one of these methods helps you obtain the instruction manual you need for your Robic sc-800 el stopwatch/timer
Why my Fx-570EX calculator mirrored/inverted
If your Casio Fx-570EX calculator is mirrored or inverted, it's possible that you accidentally activated the mirror mode or the inverse mode.
To turn off mirror mode, you can follow these steps:
- Press the "Mode" button on your calculator.
- Use the arrow keys to select "Setup" and press the "OK" button.
- Use the arrow keys to select "Screen" and press the "OK" button.
- Use the arrow keys to select "Mirror" and press the "OK" button.
- Select "Off" and press the "OK" button.
To turn off inverse mode, you can follow these steps:
- Press the "Shift" button followed by the "Mode" button.
- Use the arrow keys to select "Setup" and press the "OK" button.
- Use the arrow keys to select "Screen" and press the "OK" button.
- Use the arrow keys to select "Inverse" and press the "OK" button.
- Select "Off" and press the "OK" button.
If the above steps do not work, you can try resetting your calculator to its default settings. To do this, you need to press and hold the "Shift" button followed by the "AC" button.
My seca 813 only showing STEP OFF AND STOP massage cannot reset ??
If your Seca 813 is only showing the "STEP OFF" and "STOP" messages and is not responding to any commands, it is possible that there is a problem with the scale's sensors or the internal circuitry. Here are some steps you can take to troubleshoot the issue:
- Make sure that the scale is on a flat and stable surface. If the scale is on an uneven surface or is wobbling, it may not be able to take accurate readings and could display error messages.
- Check the scale's batteries. If the batteries are low, this could cause the scale to malfunction. Replace the batteries with fresh ones and try turning the scale on again.
- Reset the scale. Some scales have a reset button or function that can be used to clear any errors or malfunctions. Refer to the user manual for instructions on how to reset your specific model of scale.
- Check the scale's sensors. Over time, the sensors on a scale can become dirty or worn, which can affect their accuracy. Clean the sensors with a soft cloth or brush and see if this resolves the issue.
- If none of the above steps work, you may need to contact Seca support or a professional technician for further assistance. They may be able to diagnose the issue and recommend a repair or replacement if necessary.
Roberto biaci floreca watch
To turn on your Roberto Bianci watch, you need to locate the crown on the side of the watch and unscrew it gently by turning it counterclockwise. Once you have unscrewed the crown, pull it out gently to the first position. This should activate the watch and allow you to set the time by turning the crown clockwise or counterclockwise. Once you have set the time, push the crown back in and screw it back in gently by turning it clockwise until it is snug. The watch should now be turned on and ready to use. If you continue to have difficulty turning on your watch, you may want to refer to the instruction manual or contact the manufacturer for further assistance.
Why my fujixerox 203A, all lamp is blinking?
If all the lights are blinking on your Fuji Xerox 203A printer, it is indicating a "Fatal Error" or "Unknown Error" that has occurred.
Here are some possible reasons and troubleshooting steps you can try:
- Paper jam - Open the printer cover and check for any paper jams. If found, clear the jam and close the cover.
- Toner cartridge issue - Remove the toner cartridge and check if it is empty or low. If so, replace the toner cartridge with a new one.
- Imaging drum issue - Remove the imaging drum and check if it is damaged or has reached the end of its life. If so, replace the imaging drum.
- Connectivity issue - Check the printer connections to ensure they are securely plugged in.
- Firmware issue - Try updating the firmware on the printer to see if that resolves the issue.
If none of these steps solve the issue, you may need to contact Fuji Xerox customer support for further assistance.
HITI C290 RIBBON ERROR 0201
rror code 0201 on the HiTi C290 printer indicates a problem with the ribbon. Here are some steps to troubleshoot the issue:
- Open the printer cover and remove the ribbon cassette.
- Check the ribbon for any damage or wrinkles. If there is any damage, replace the ribbon with a new one.
- Ensure that the ribbon is installed correctly in the cassette and that the cassette is inserted properly into the printer.
- Check the ribbon sensor to ensure it is clean and free from any dirt or debris. You can clean the sensor using a soft cloth or cotton swab.
- If the problem persists, try resetting the printer by turning it off, unplugging it from the power source for 5-10 minutes, and then plugging it back in and turning it on again.
- If none of these steps work, contact HiTi customer support for further assistance.
When i turn ON the
could you fix your roland plotter, because appears the same in my screen temperature is too low even is not, how can you fix this problem thanks
Kodak ESP 5250 printer. Replaced ink cartridges and print head. Still won't print.
There are several things that could be causing your Kodak ESP 5250 printer to not print even after replacing the ink cartridges and print head. Here are some troubleshooting steps you can try:
- Make sure the cartridges are installed correctly: Double-check that the ink cartridges are correctly installed in the printer. The cartridges should click into place and the lock lever should be in the down position.
- Run a cleaning cycle: If the ink cartridges are installed correctly, run a cleaning cycle to clear any clogs in the printhead. Go to the printer's menu and look for a "clean printhead" option.
- Check ink levels: Make sure that the ink levels are sufficient for printing. Check the ink level indicator on the printer's display screen.
- Check for error messages: Look for any error messages on the printer's display screen or on your computer. If there is an error message, follow the instructions to resolve the issue.
- Restart the printer: Sometimes simply restarting the printer can resolve issues. Turn off the printer, unplug it from the power source, and wait a few minutes before plugging it back in and turning it on again.
If none of these steps resolve the issue, it may be a more serious hardware issue with the printer that requires professional repair.
I have a cp3525 that has a 59.F0 error on startup. I have run the physical alienation test and the itb contact/alienation test. Both seem ok but the error persists. Any ideas?
A 59.F0 error on an HP Color LaserJet CP3525 printer typically indicates an issue with the intermediate transfer belt (ITB). The ITB is responsible for transferring toner from the cartridges onto the paper during the printing process.
If the physical alignment and ITB contact tests have not resolved the issue, there are a few other things you can try:
- Check for any torn or damaged paper stuck in the printer. This can cause the ITB to become misaligned or damaged.
- Replace the ITB. If the ITB is worn out or damaged, it may need to be replaced.
- Check the ITB motor. The ITB motor is responsible for driving the ITB. If the motor is malfunctioning, it can cause the ITB to become misaligned or damaged.
- Reset the printer. Sometimes resetting the printer can clear up error codes. To reset the printer, turn it off, unplug it from the power source, wait 30 seconds, and then plug it back in and turn it on again.
If none of these solutions work, you may need to contact HP support or a professional technician for further assistance.
Promethean prm-35 windows 10 driver
The Promethean PRM-35 is a projector, and it does not require any drivers to work with Windows 10.
To connect the PRM-35 to a Windows 10 computer, follow these steps:
- Connect the projector to your computer using a VGA or HDMI cable.
- Turn on the projector and set it to the correct input mode (VGA or HDMI).
- On your computer, go to the "Display settings" and select "Extend desktop" or "Duplicate desktop".
- Adjust the resolution and scaling settings to match the projector's native resolution.
- Your computer's display should now appear on the projector.
If you are having trouble getting the projector to work with your computer, try using a different cable or input mode, and make sure the projector is set to the correct input.
I have a richo MPC 2011 when I tried to pirn or copy black/White it comes out blank please I need help
If your Ricoh MPC 2011 is printing or copying blank pages when trying to print or copy in black and white, it is possible that the toner cartridge is either empty or defective. Here are a few steps you can take to troubleshoot the issue:
- Check the toner level: Check the toner level in the printer to ensure that it is not empty or low.
- Replace the toner cartridge: If the toner level is low, try replacing the toner cartridge with a new one to see if that resolves the issue.
- Clean the printer: Dust and debris can sometimes accumulate inside the printer, which can affect print quality. Try cleaning the printer to remove any dirt or debris that may be interfering with the printing process.
- Check the settings: Make sure that the printer settings are configured correctly for black and white printing.
If none of these steps work, it may be necessary to contact a printer technician for further assistance.
E2 on a deraflame heater?
The E2 error code on a Duraflame heater usually indicates a problem with the temperature sensor or the control board. Here are some steps to troubleshoot and fix the E2 error code:
- Turn off the heater: Turn off the heater and unplug it from the power source.
- Check the temperature sensor: Locate the temperature sensor on the heater and check that it is connected properly and not damaged. If the sensor appears to be damaged, it may need to be replaced.
- Check the wiring: Inspect the wiring connected to the temperature sensor and make sure there are no signs of damage or fraying. If the wiring is damaged, it may need to be repaired or replaced.
- Reset the heater: If the temperature sensor and wiring appear to be in good condition, try resetting the heater. This can be done by unplugging the heater and waiting for 10-15 minutes before plugging it back in.
- Replace the control board: If the above steps do not fix the problem, the issue may be with the control board. In this case, the control board may need to be replaced. However, replacing the control board can be complex and is best left to a qualified technician.
It is important to follow any safety instructions provided by the manufacturer and to avoid attempting any repairs if you are not comfortable with electrical troubleshooting.
Power cord is stuck sunbeam 4214
If the power cord is stuck in your Sunbeam 4214 appliance and only comes out 5 inches, there are a few things you can try to release it:
- Check the cord for any visible damage or kinks that could be causing it to get stuck. If you see any, gently straighten them out or replace the cord if necessary.
- If the cord is stuck due to corrosion or dirt buildup around the power cord receptacle, you can try cleaning the receptacle with a small brush or compressed air to remove any debris.
- If the cord is stuck due to a faulty locking mechanism, you may need to disassemble the appliance to access the locking mechanism and release the cord. Refer to the appliance's user manual or seek assistance from a qualified technician for guidance on how to safely disassemble the appliance.
- If the cord is stuck due to a problem with the internal wiring or components of the appliance, it may be necessary to replace the faulty part or have the appliance repaired by a qualified technician.
Not finding what you are looking for?
