20 Most Recent
Sunbeam SMW750 Microwave Oven - Page 4 Questions & Answers
Microwave quit when door was open
yes,unplug the unit,take the screws out of the side and back lift the cabinet up and off and you will see a fuse right on top replace it.hope this helps
5/19/2014 8:35:58 PM •
Sunbeam...
•
Answered
on May 19, 2014
It wont turn on
make this test and fix it. God bless you
- Inspect the power cord Unplug the power cord and check for voltage at the outlet. Also inspect for damage, shorts, or burn marks that can be a possible safety hazard.
- Bad door switch If your microwave does not work at all and you know everything is plugged in properly and the outlet is functioning, then also check the door hooks and the door release button. Using a volt-ohm meter on RX1, check your terminals. When your microwave door is closed you should have a reading of zero. Once the door is open the reading should change to infinity. If these readings do not match up, replacement of the door switch is necessary.
- Blown fuses To determine if your fuse has blown out, which may attribute to your microwave not running, you need to pull the fuse out using a pair of fuse pullers. Lay it down and using a volt-ohm meter on RX1, check both ends of the fuse in question. If you do not get a reading of zero, then you will need to replace the fuse.
- Bad fan motor Locate the fan and remove the leads. Again using the volt-ohm meter on RX1, check the terminals. If an infinity reading is displayed, it means that the fan has gone bad and requires replacement.
12/10/2013 12:30:41 PM •
Sunbeam...
•
Answered
on Dec 10, 2013
I bought a mircowave and i plugged it in and it wont turn on
make this steps and fix it. God bless you
- Inspect the power cord Unplug the power cord and check for voltage at the outlet. Also inspect for damage, shorts, or burn marks that can be a possible safety hazard.
- Bad door switch If your microwave does not work at all and you know everything is plugged in properly and the outlet is functioning, then also check the door hooks and the door release button. Using a volt-ohm meter on RX1, check your terminals. When your microwave door is closed you should have a reading of zero. Once the door is open the reading should change to infinity. If these readings do not match up, replacement of the door switch is necessary.
- Blown fuses To determine if your fuse has blown out, which may attribute to your microwave not running, you need to pull the fuse out using a pair of fuse pullers. Lay it down and using a volt-ohm meter on RX1, check both ends of the fuse in question. If you do not get a reading of zero, then you will need to replace the fuse.
- Bad fan motor Locate the fan and remove the leads. Again using the volt-ohm meter on RX1, check the terminals. If an infinity reading is displayed, it means that the fan has gone bad and requires replacement.
12/10/2013 12:25:40 PM •
Sunbeam...
•
Answered
on Dec 10, 2013
I have sunbeam .9cuft microwave model:SGB8901 may
follow this steps and fix it. God bless you
- Main control boardIf
your microwave runs for a few seconds and stops, the first thing to
check is the main control board to ensure that a shortage has not
occurred. If the part is defective then it will need to be replaced to
prevent continual shut offs. If this is not the issue, the next step
would be to check for a faulty touchpad.
- Touchpad/Control panelIf
the control board is not the issue and your microwave continues to shut
off after running for only a few seconds, the next thing to check is
your touchpad, which is also known as a control panel. Although uncommon
for this issue, symptoms are usually that the display and some buttons
are working properly; however, when selected some buttons are not
functioning. If this is the case the touchpad will need to be replaced.
10/24/2013 12:50:13 PM •
Sunbeam...
•
Answered
on Oct 24, 2013
I have SUNBEAM microwave, model
After a long search and reading I finally got it. To adjust power level follow these instructions:1. Set timer for amount of minutes you want.2. Hit "power" button"3. Change the power from 100% to another percentage by hitting numbers 1-94. Press Start
10/21/2013 1:15:04 AM •
Sunbeam...
•
Answered
on Oct 21, 2013
Not finding what you are looking for?