20 Most Recent American Standard Cambridge 5 Ft. x 32" Right-hand Drain Whirpool Tub, Whit - Page 8 Questions & Answers


bdujwu7ye je9809 l,ldchr fk;lkjf

American... | Answered on Feb 11, 2011


"deep six" it
American Standard brass is ****!

American... | Answered on Dec 30, 2010


Unscrew the pop-up cable connector from the drain tail-piece and rotate the screw on the side 180 degrees. Reattach the cable adapter.

American... | Answered on Dec 23, 2010


Hi Tom. Get a set of allen wrenches, insert one after another into the hole until one catches on that allen screw. You could also get a small mirror and a flashlight and look into the hole. I can assure you that there is an allen screw in there. It is just a matter of finding the correct allen wrench and getting it seated into the allen screw.

Go to this link http://www.ehow.com/how_4896394_remove-american-standard-ball-faucet.html
to see the step by step instructions

Joe
Thanks for choosing Fixya!

American... | Answered on Dec 20, 2010


try reversing your hot and cold lines

American... | Answered on Dec 10, 2010


Tub spout threads onto end of pipe. The diverter does not play a role.

Sometimes these things get rusted in place, and you have to bend them getting it off.
When all else fails, get a big pipe wrench and muscle it until it bends up and comes off.
Sounds like you might need a new tub spout ... and might need a new pipe ... be sure to match length of pipe to depth of threads on new spout.

Photos from google-image search for "tub spout removal tool"
http://www.justingermino.com/replacing-bath-tub-spout/
geno_3245_115.jpg
geno_3245_116.jpg

American... | Answered on Nov 27, 2010


Howdy. We are FixYa.com and I am Farmerbear. How can we help you today?

American... | Answered on Sep 10, 2010


Replacing the spray diverter or faucet cartridge ( depending on your model) will fix the problem. Call American Standard and ask for free replacement parts.

American... | Answered on Sep 09, 2010


Chisel notch on inside of drain away from tub & hit it counter clockwise until it unthreads from lower section.

American... | Answered on Aug 10, 2010


don't we all !!!

American... | Answered on Aug 10, 2010


??? please explain!!

American... | Answered on Aug 06, 2010


it is called hydraulic hammer nd meant that you have very good pressure in your lanes, if it start suddenly, this meant that your air chamber lost it's air, in that case simplest solution will be as follows:

1. close the mains,
2. open all taps (fawcets) and drain all water from the system,
3. close all taps (fawcets)
4. open mains and check if hammer is still present.

if hammer is still present, that meant you need to clean your airchamber, you need to find where it is lockated, follow steps 1 and 2, open airchamber, check if any debris inside and clean, re-seal the chamber, then follow steps 3 and 4.

if hammer was always, this meant that you do not even have airchamber. you can install one easy for yourself, just purchase one, and best place for it is on the end of the line, somehere close to most offending faucet.

if you find this advice helpfu, please do not hesitate leave your remark and give me your vote, thanx!

American... | Answered on Aug 02, 2010


So are you going to build your own? Is it going to be for cold water only? Cheaper to buy a safe manufactured one. And a bladder tank is even better : Shell thickness: The minimum thickness
of a shell shall be determined using the
following equation:
Ts = PR/ES
E = Weld efficiency for longitudinal welds
(0.85).
NOTE: E = 1 if 100% of production
is tested at the maximum
working pressure.
S = Yield strength 20,000 psi
(140,000 KpA) or greater if certified
by the manufacturer.
See this link. http://www.watersystemscouncil.org/VAiWebDocs/standards_docs/ANSI_Final_0905.pdf

American... | Answered on Jul 17, 2010


hi, sorry no answers for your homework but check out this link and the example at the bottom of the page is what you need
http://www.coilgun.info/theoryinductors/dampedoscillator.htm
hope this helps


American... | Answered on Jul 14, 2010

Not finding what you are looking for?
American Standard Cambridge 5 Ft. x 32" Right-hand Drain Whirpool Tub, Whit Logo

11 questions posted

Ask a Question

Usually answered in minutes!

Top American Standard Plumbing Experts

Bill Johnson

Level 2 Expert

306 Answers

john h

Level 3 Expert

23515 Answers

Fahr Quad

Level 3 Expert

774 Answers

Are you an American Standard Plumbing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

American Standard Plumbing

  • American Standard Plumbing

Most Popular Question

bath tubs installation

  • Plumbing
Loading...