20 Most Recent TechnoMarine RSQC11 Wrist Watch Questions & Answers


Thank you for contacting FixYa.
NEVER attempt to replace a battery on a diving watch yourself. It will break the seal.
You will need to send back to Technomarine or take to a registered Technomarine service center.
You can find information here:
http://www.technomarine.com/Customer/Services.sls

Best regards! Jewel

TechnoMarine... | Answered on May 26, 2018


It is possible. Open the watch case back, memorize all the writings on watch battery as well as how the battery is positioned (+ and -). Buy exactly the same battery, replace it and close the case back. To be sure case back is closed as tight as it was, draw fine line across the case and case back with non-permanent marker. This will help you align when closing the watch and you can clean it off later. Rate me, please.

TechnoMarine... | Answered on Apr 26, 2010


You may have arrows inside bracelet.Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and start to unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet,make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
Don't forget to rate, please.

TechnoMarine... | Answered on Jan 10, 2009


Sounds like the main drive is not "engaged" or you are in "stop watch" mode. Check to make sure you are in the correct mode. Then check to see if you can change the hour/minute hands. Reset the time and re-engage. See if that corrects the problem. (You've probably have done this already)

The watch has a 2 year warentee plus because it's water resistant down to 330 feet, I would take it back or to an authorized dealer to have it repaired. Other wise you stand the chance of damaging as really nice watch. And while you are there have them explain all the features. Really is a nice watch.

TechnoMarine... | Answered on Nov 18, 2007


If you can't return it as defective, take it to a jeweler for repair.

TechnoMarine... | Answered on Mar 02, 2019


Fixya is unable to suggest sources for Technomarine belt/straps.

TechnoMarine... | Answered on May 31, 2018


take it back for a warranty inspection
it could be a simple flat battery

TechnoMarine... | Answered on Dec 07, 2015

Not finding what you are looking for?
TechnoMarine RSQC11 Wrist Watch Logo

6 questions posted

Ask a Question

Usually answered in minutes!

Top TechnoMarine Watches Experts

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

842 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

33395 Answers

john h

Level 3 Expert

23424 Answers

Are you a TechnoMarine Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

TechnoMarine Watches

  • TechnoMarine Watches

Most Popular Question

possible change battery

  • Watches
Loading...