Question about 2004 Skyteam ST 200
Hello, I have just rebuilt my skyteam 200cc dirt bike. it starts on the first kick. when I put the bike in any gear it cuts out but I don't have a kill switch on it just yet. I'm not sure if that's the problem/ hope you can help thanks @
Hi, Frazergallow and the usual suspects are:
1. Faulty wiring to any safety switch.
2. Safety switches loose at the mounting point.
3. Faulty kickstand safety switch.
4. Failed kickstand safety switch circuit diode.
5. Stretched side stand spring.
6. Side stand not coming up far enough to disengage switch.
7. Faulty clutch lever safety switch.
8. Faulty neutral safety switch.
9. Clutch not properly adjusted.
10. Clutch plates sticking, forward lurch
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Posted on Jan 15, 2020
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: No power.
I know you have cleaned the carb but ya gotta keep at it. The jets are not the problem. The problem is the little pilot circuits for low and early mid range fuel supply. Varnish or trash in the carb can be very hard to get rid of.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
Remove the carb and then the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well. Be liberal with the spray. Also use compressed air to blow out the passage ways.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Before putting the slide back into the carb, move the clip on the jet needle down one notch. Put the rest of the carb back together and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.
Please rate this solution. Thanks!
Posted on Apr 17, 2009
SOURCE: Skyteam ST 125 TR parts
i have blown the fuse on my skyteam motocycle but it was soon replaced but for some reason there is no spark coming out of the spark plug someone help plz
Posted on Sep 10, 2010
M & C Motorcycle Repair (5) Read Reviews ' Write a Review
Tires, Brakes, Suspensions & Alignments - Done While You Wait. Come Visit Our New Location.
901 E 4th St, Long Beach, CA 90802
[email protected] (562) 436-3926
Posted on Mar 09, 2011
Tips for a great answer:
Mar 01, 2014 | Yamaha Motorcycles
Jun 03, 2013 | Pit Bike 125cc 4 Stroke Dirt Bike
Apr 25, 2012 | Pit Bike 125cc 4 Stroke Dirt Bike
Oct 26, 2010 | Bajaj Pulsar 150 Motorcycles
Jul 09, 2009 | 2004 Skyteam ST 125 TR
Apr 06, 2009 | 2002 KTM SX 250
Jan 23, 2009 | 2000 Yamaha DT 125 R
74 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: