Question about 2005 kawasaki KX 250

1 Answer

Water in oil fill glass - 2005 kawasaki KX 250

Posted by whitetail96 on

Ad

1 Answer

A Miller

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • kawasaki Master
  • 8,404 Answers

Change your oil immediately - replacing with the proper quantity and quality lubricant recommended by Kawasaki.

Posted on May 02, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How often do you fill pump wit oil?


Pump oil doesn\'t need to filled often. Only when you notice the oil looking creamy or not clear! This applies only to horizontal shaft pumps! If you have a vertical shaft, the pump is non-serviceable. If the pump is leaking oil, then only add as needed! The oil level on any pump is half way up the sight glass if any is available. If no sight glass is available then only half way up! NEVER fill the pump completely up! This can cause oil seals to fail as well as other damage to the pump! Best of luck!

Sep 26, 2014 | Garden

1 Answer

Pump blowing oil out of fill spout model 67546


is the oil milky in color need more info on pump,does it have a sight glass is water dripping from underneath head???let me know

Jul 31, 2013 | Garden

1 Answer

No sight glass on my Generac Pressure washer nothing to tell me how much oil to use


TAKE YOUR PINKY FINGER AND TAKE AND PLACE IT IN THE OIL FILL YOU BE ABLE TO TOUCH HE OIL THERE IS ALSO A SLIT INSIDE THE OIL FILL INSIDE OF OIL FILL .FILL THE OIL FILL TO THE POINT THAT THA IT COVERS THE TOP THE SLIT BUT DONT OVER FILL THE MOTOR THE OIL SHOULD JUST COVER THE SLIT I HOPE THAT THIS WILL HELP YOU

Apr 19, 2013 | Generac Generator 5989 2,700 PSI 2.3 GPM...

1 Answer

WHERE IS THE( OIL DIP STICK) ON A 1980 HONDA 500CX


I have an old bike also, no dip-stick, but theres a sight glass on the right side of the engine, down low on the side case, you should put it on the center stand first and add oil slowly until you see the oil in the sight glass, only fill it 1//4 of the way, start bike, run for 30 second- to 1 minute the turn it off and check the level when it cools down again, add more oil slowly as needed but dont fill above halfway in the sight glass.

Sep 25, 2012 | 1980 Honda CX 500 A

1 Answer

How do you check the oil on a the subject bike?


on the right side close to the bottom , there is a hole in the plastic. You should be able to see through it to the engine. The glass hole there is the levewl marker for the oil. Have someone hold the bike straight up and the glass should fill with oil. As long as its half or better filled, the oil level is fine.

Jun 06, 2011 | Harley Davidson XL 1200 C Sportster Custom...

2 Answers

What oil to use in the power washer water pump


Oil used in engine is SAE30, I would suggest adding bit of Nulon or similiar Teflon based before even first run as it will extend life of the engine, This is air cooled Honda and therefore overheat easy.

Oil used in pump is Universal Tractor Transmission Oil.

Except two, all pumps are equiped with sight glass, fill as indicated on sight glass or dipstick.

To extend life of your equipment, change oil in both, engine and pump after 50hrs.

If you live in colder climates, where freezing is possible, do not forget to drain pump and high pressure hose from water to avoid winter damage.

Hope this will help keep your equipment in top notch for years to come:-)

Jun 22, 2010 | Northstar Pressure Washer 3000 PSI

1 Answer

No ice or water from in-door dispenser


When you first hook water up to the refrigerator you have to fill a tank in the fridge. Open the water supply behind the ref. turn the control on the front of the ref to water and hold a glass under the spout as if you are filling a glass . You may have to wait 3-4 minutes forthe tank and lines to fill with water before you get any to come out into the glass. The water my be discolored at first so run a few glass full through before drinking . hope this helps

Bobalix

Apr 16, 2009 | Kenmore 55612 / 55614 / 5561 / 655619 Side...

1 Answer

Drain and change oil


I can't tell you all the particulars from the limited amount of pictures of your bike. -Remove the oil drain bolt on the bottom of the crankcase (the universal bolt size for bikes use a 17mm wrench). -Drain the oil (remember to recycle). -Re-install the drain bolt with a new sealing washer if necessary. -The oil fill cap should be some where on the top of the crankcase. About 1 or 25mm in diameter with a raised tab for turning. -Fill with recommended oil. -There are 2 ways to check oil level on dirt bikes: 1) Oil level check bolt. On the right side cover. 2) Oil level site glass. A 1 round piece of glass on the side of the crankcase. Usually by the kick start & R brake lever. -Always check the oil level with the bike upright (as if you were sitting on it). -Check bolt - fill with oil slowly until oil comes out of the check bolt and re-install it. -Sight glass - fill with oil to cover 3/4 of the sight glass. -Remember to hold the bike upright when adding oil.,

Nov 10, 2008 | 2008 Derbi Senda Baja 125 R

Not finding what you are looking for?
2005 kawasaki KX 250 Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6480 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

217 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...