Error code 46. - 2007 Yamaha YZF-R6

Very good article for what this error is and how to fix it here:
brother error code 46

Clear browser cache and history, get malwarebytes free version and run it.;

Error 46

Description Pacific 3


Detected by VIPER

Device T6TF4HFG


Error/ Prot E

These info are for qualified service technicians.

error 46 is charging system not working normal, google error code 46 seems to be common on this bike

46- power supply to the FI system relay is not normal,

probable cause of malfuction:

1. open circuit in wiring harness (red/blue line )
2.malfunction in charging system
See here for further info,
http://www.r6messagenet.com/forums/r6-warranty-premature-failure/31664-error-code-46-a.html

Many thanks - I fixed the error 46 by following the helful solution provided below.

mydcp110c


Rank: Apprentice
Rating: 86%, 8 votes
Hello!

Here is the "Unable to Clean" (code 46) solution:

The machine counts all purge (cleaning) operations in order to prevent the internal ink absorber box from overflowing with purged ink. An “initial purge”, for example, advances the purge counter by 187 + 420 = 607. When the purge counter approaches 6400, an internal "Machine Error 46" is generated. Further purge operations are prohibited, and therefore the printer becomes unuseable.

When an internal Machine Error 46 is generated, the user will see an “Unable to Clean” external message and will be unable to use the printer. The “Unable to Clean” external message can relate to many different internal error codes however.

The user can establish the internal Machine Error Code as follows: pull the mains cable out of the machine (power off), hold down the Menu/Set key, re-insert the mains cable into the machine (power on). The internal Machine Error Code will be displayed.

If there is a Machine Error 46, it is necessary to dismantle the printer, replace the ink absorber box (or possibly break the ink absorber box open and clean its absorbent sponges under a tap), re-assemble the printer and reset the purge counter to zero.

Solution no. 1. (DCP-110C):

The proper reset code sequence to reset DCP printers without numeric keypad should be as follows:

1. press buttons Set, Menu, Mono Start one by one, followed by up arrow key four times.this should all be done as short a time as possible, around 3 seconds.

2. enter maintenance mode 80 by pressing the up/down arrow key and set key to select numbers 8 and 0

3. press up arrow key several times to get to the Purge item

4. enter 2, 7, 8 and 3 using arrow/set keys to reset the counter

5. press Stop/Exit key to go to root of maintenance mode

6. enter 9,9 to exit maintenance mode

Here is the answer to the Machine Error 46 (have just fixed my own MFC210C):


Machine Error 46 – Purged Ink Box Full MFC620CN/420CN/410CN/210C and FAX2440C

The machine counts all purge (cleaning) operations in order to prevent the internal ink absorber box from overflowing with purged ink. An “initial purge”, for example, advances the purge counter by 187 + 420 = 607. When the purge counter approaches 6400, an internal "Machine Error 46" is generated. Further purge operations are prohibited, and therefore the printer becomes unuseable.

When an internal Machine Error 46 is generated, the user will see an “Unable to Clean” external message and will be unable to use the printer. The “Unable to Clean” external message can relate to many different internal error codes however.

The user can establish the internal Machine Error Code as follows: pull the mains cable out of the machine (power off), hold down the Menu/Set key, re-insert the mains cable into the machine (power on). The internal Machine Error Code will be displayed.

If there is a Machine Error 46, it is necessary to dismantle the printer, replace the ink absorber box (or possibly break the ink absorber box open and clean its absorbent sponges under a tap), re-assemble the printer and reset the purge counter to zero.


Resetting purge counter MFC620CN/420CN/410CN/210C and FAX2440C

1) Enter machine maintenance mode (on MFC210C all four photo/copy/fax/scan lights flash in maintenance mode). Care is needed in maintenance mode, otherwise critical settings may be inadvertently corrupted.

FAX models with numerical keypads: Press the Menu/Set, *, 2, 8, 6 and 4 keys within two seconds. (if you fail to complete the correct key sequence within two seconds, press the Stop key to try again).

Other (non-FAX) models: Press the Menu/Set and Black Start keys. Next press the “up arrow” key four times to enter the maintenance mode).

2) Press the 8 then 0 keys in the initial stage of the maintenance mode to call up the machine's log information list (function code 80).

3) Press the Black Start key several times to scroll through the log information list to reach the purge counter. The purge counter is the 25th item in the list.

4) Press the 2, 7, 8, and 3 keys in this order to reset the purge count to zero.

5) Press the Stop/Exit key to return to the initial stage of the maintenance mode.

6) Press the 9 key twice to return to the standby state.

Carry on printing !!

thanks.

A 46-11 code indicates a communication failure between the A/D converter board and the main control board. Likely a bad or poorly seated ribbon cable. Try to reset the machine by turning off the main power switch on the side of the machine for 10 seconds and re-powering up. If the problem persists you will need to call a technician.

Communication report codes
46 NO RESPONSE The FAX signal from the remote party is not detected within T1 time. <Send/Polling>