Question about Harley Davidson FXD Dyna Super Glide Motorcycles

1 Answer

How much fork oil goes in the forks of an 2001 FXD and how do I do this ? Do you have any diagrams to help me with ?

Posted by chromeboned on

Ad

1 Answer

jfhinton45

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers



I have no diagrams for you. MAke your own as you take it apart etc and take lots of cell phone pictures if you need help remembering how to put things back together.

Table 1-6. Type E Fork Oil Amounts



MODEL OZ CC IN. MM



FXDXT 11.5 341 6.10 154.9



FXDWG 12.0 356 7.28 184.9



FXDL 10.7 316 7.20 182.9



FXD 10.6 314 6.69 169.9




Changing fork oil is a simple mater for some models and requires fork disassembly for others. Here is the procedure for all 2001 DYNA models:

2001 DYNA FRONT FORK OIL 1.18


REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.






Posted on Nov 16, 2014

Ad

5 Related Answers

robotek

Graeme Ross

  • 1512 Answers

SOURCE: front fork oil capacity

Hi
You can download the whole workshop service manual that has this info and heaps more from here. Hope this helps Thanks for using Fixya. 
regards robotek

Posted on Jan 10, 2009

Ad

Ken Mangione

  • 74 Answers

SOURCE: Fork oil level: 2006 KDX 200

This all depends on what size forks you have, but a good rule of thumb is 120ml. After that then what you want to do is to ride the bike and make adjustments to your front end until your liking.

Posted on Jan 16, 2009

tellme2

terry weightman

  • 137 Answers

SOURCE: fzr1000 fork oil

hello m8,,i had one of these babys,,grab your self a medium grade oil,, if u have a litre bottle u need to put just over a quarter of that bottle in each fork,, or if u have a 500ml bottle pour half a bottle in each fork,, cheers

Posted on Mar 24, 2009

tombones

  • 3567 Answers

SOURCE: Fork Oil Capacity

Use Yamaha suspension oil #01. Amount is 19 ounces. Oil level from top surface w/o cap nut is 3.15" to 5.51". I am sending you a link to a site where you can download a free shop repair manual. It is actually a bit complicated as you will see in the manual.

http://www.carlsalter.com/motorcycle-manuals.asp

Top rating due on this one! Thanks!

Posted on Apr 24, 2009

hawk127311

CURT

  • 350 Answers

SOURCE: how much 5w oil goes into each fork?

Using 5w oil with stock springs, your oil level should be about 100mm from the top with the fork fully compressed, damper rod pushed all the way down, and the spring out. I hope this helps and good luck. Please vote and leave a message.

Posted on Oct 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 FXD - What are the specs for front fork travel and how do I change the tube oil?


You are going to need a service manual, it is too long a process to go into right here. Use Harley type E fork oil

Sep 17, 2014 | 2001 Harley Davidson FXD Dyna Super Glide

2 Answers

2001 FXD - What are the specs for front fork travel and how do I change the oil if needed in the fork tubes?


There are no specs for front fork travel. The forks will travel from full compression to full extenison. Use Harley type E fluid.

Sep 17, 2014 | Harley Davidson FXST Softail Standard...

1 Answer

How to change fork seals in a 2008 fxd


To change the fork seals in a 2004 FXD you will need to remove the forks from the bike and then drain the oil and then remove the dust seal and the retaining ring and spacer from the top of the fork and then remove the Allen head screw from the bottom of the fork to release the fork tube and then using the fork tube like a slide hammer drive the upper bushing, seal and spacer out the top of the slider. While apart you should also inspect the rings and bushings etc. You will need a special seal driver to reinstall the upper bushing, seal and spacer and then you will need to accurately refill the fluid to the correct level/amount. FXD/FXDL uses 10.6 OZ or 0.31 cc of Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) and the level measurement is 6.69 inches or 169.9 mm. Be very careful and accurate with the oil level as too much or too little will adversely affect the function, ride and steering of the bike. It is best to use a fork oil level gauge and set it so that the ring will sit 6.69 inches or 169.9 mm from the end of the tube and secure it at that position. If your gauge has a plunger cylinder on it push the plunger on the cylinder all the way in and then with the fork tube bottomed in the fork slider, insert the tube until the ring rests flat on top of the fork tube and pull the plunger out to suck up excess oil from the fork tube. If no oil is sucked up into the gauge cylinder you need to add more oil until there is enough excess oil in the fork tube to have an excess amount sucked out of the fork tube. In this manner the gauges and cylinder will accurately set the fork oil level. If you have a vacuum operated gauge such as with a tool that attaches to a vacuum brake bleeder you will set the tool at 6.69 inches or 169.9mm as with the other type of tool and operate it the same way to remove excess oil to a precise and accurate specified fork oil level which is very important as an incorrect oil level can adversely affect motorcycle handling.

Jul 12, 2014 | 2004 Harley Davidson FXD - FXDI Dyna Super...

1 Answer

Fxdl fork oil capacity


2001
FXDWG
FXDL
FXD
FXDX
FXDXTFRONT FORK-- ALL = 9.2oz .27 litre

Apr 30, 2014 | 2001 Harley Davidson FXDL Dyna Low Rider

1 Answer

2001 fxdl fork oil capacity


2001
FXDWG
FXDL
FXD
FXDX
FXDXTFRONT FORK-- ALL = 9.2oz .27 litre

Apr 30, 2014 | 2001 Harley Davidson FXDL Dyna Low Rider

1 Answer

What is the 2001 fxdl fork oil capacity?


2001
FXDWG
FXDL
FXD
FXDX
FXDXTFRONT FORK-- ALL = 9.2oz .27 litre

Apr 30, 2014 | 2001 Harley Davidson FXDL Dyna Low Rider

1 Answer

How to drain fork oil on 2010 fxd harley


Hi Anonymous, please website below and good luck:
How to Change the Fork Oil on 2012 Harley Davidson Street Glide

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Jan 18, 2014 | Harley Davidson Motorcycles

1 Answer

Whats the oil capacity in my forks(1996 FXD Dyna super glide


Hi Anonymous, for more information on your question please visit the websites below and good luck:
Cycles Capacities and Fluid Requirements Fork Filling Quantities

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Feb 06, 2013 | 2000 Harley Davidson FXD Dyna Super Glide

1 Answer

How do you remove the forks on a 2001 fxd superglide






Hopefully you will glean all you need to know from this but if you want or need more information or more FXD specific information PLEASE H

Hopefully the information below will be okay BUT if you need any more or any more specific information please post a comment and describe what you want/need.

REPLACING FORK OIL Replace front fork oil at every 20,000 mile (32,000 km) service interval and/or prior to storage.


ALL BUT FXDX & FXDXT models


Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, on FXDL models, remove the center plug from each fork cap, on all other models, remove the fork tube caps, remove the drain screws from the bottom of each fork and drain the fork oil, replace the drain screws and washers and tighten the screws

to 13-17 in-lbs (1.5-2.0 Nm) THEN see Table 1-6. and fill the fork with Harley-Davidson TYPE E FORK OIL (Part No. HD-99884-80) as set out in the Table. THEN if apart assemble the forks as follows:


a. FXD, FXDXT, FXDWG models: install both fork tube caps and tighten them to 11-22 ft-lbs (14.9-29.8 Nm).

b. FXDL models: install center plugs and tighten until secure.


Fork oil amounts can be measured two ways: use the oz./cc measurement if fork is left in frame; use the in./mm measurement if the fork is disassembled in which case the oil level is measured from the top of the fork tube with the spring removed and the fork fully compressed.


Table 1-6. Type E Fork Oil Amounts for 2001 DYNA


MODEL OZ CC IN. MM

FXDXT 11.5 341 6.10 154.9

FXDWG 12.0 356 7.28 182.9

FXD 10.6 314 6.69 169.9


PART NO. SPECIALTY TOOL

HD-41177 Fork tube holder

HD-41549A Fork spring compression tool

HD-41551 Spring plate tool

HD-36583 Fork seal installer

HD-59000A Pro-level oil gauge



FRONT FORKS: FXDX & FXDXT 2.20

REMOVAL

Raise and support the motorcycle so the front end is off the floor and the forks are fully extended, remove both front brake calipers and the front wheel, remove the front fender, remove the front fairing, remove the headlamp bracket and attach the headlamp to the frame using a rubber bungee strap, loosen the upper and lower triple clamp pinch bolts and pull the fork sides from the brackets.


DISASSEMBLY

Remove the stopper ring, remove the spring preload adjuster but DO NOT unthread the rebound adjuster from the damper rod because incorrect assembly could result in reduced adjustment range. THEN unthread the fork cap from the fork tube and allow the fork leg to drop, exposing the spring, THEN get a FORK SPRING COMPRESSION TOOL (Part No. HD-41549A) on the spring collar, turn the screws in to engage the holes in collar, compress the spring until the SPRING PLATE TOOL (Part No. HD-

41551) can be positioned between the spacer and the spring collar, THEN hold the fork bolt and compression adjuster, remove the fork bolt from the compression adjuster, remove the spring adjuster plate from the fork bolt, remove spacer, spring collar and spring, pour out the fork oil by pumping the fork leg and rod 8-10 times or until rod the moves freely. THEN position fork slider in vise using a FORK TUBE HOLDER such as (Part No. HD-41177) to avoid damage. THEN remove the socket head bolt, remove the damper from the fork tube, remove the cover from the slider, remove seal and stopper ring, pull the fork tube out of the slider, remove the oil seal, spacer and guide bushing from the fork tube.


CLEANING AND INSPECTION

Measure the fork spring free length and replace the spring if it is shorter than 17.00 in. (431.8 mm), check the fork tube and the slider for score marks, scratches or abnormal wear, check the slide and guide bushings for excessive wear or scratches, set the fork tube on V-blocks and measure runout which should not exceed 0.008 in. (0.2 mm).


ASSEMBLY

Coat the oil seal with TYPE E FORK OIL, before installing the slide bushing and guide bushing, lubricate them with fork oil, THEN install the guide bushing and the spacer seal noting that the guide bushing opening must be oriented to the side and NOT to the front or rear, THEN slip the slider into the fork tube, place the slide bushing over the fork tube until it rests on the slider, drive the guide bushing with the spacer seal into the slider, lubricate a new oil seal with TYPE E FORK Oil, drive the oil seal into the slider using FORK SEAL INSTALLER (Part No. HD-36583). install the stopper ring and dust seal, (if the rebound adjuster was removed from the damper rod bottom the lock nut on the threaded portion of damper rod, holding a thumb on the detent spring and ball, back out (turn counterclockwise) the rebound adjuster to the last "click." and then turn down (clockwise) 17 "clicks", thread the rebound adjuster onto the damper rod until the adjuster stops at maximum thread engagement (but do not force it), thread the locknut onto the damper rod up until it contacts the base of the rebound adjuster and tighten it in place), THEN holding the slider in a vise while being careful not to damage it. install the damper tube into the fork tube and tighten the socket screw and washer to 22-29 ft-lbs (29.8-39.3 Nm). THEN pour half the TYPE E FORK OIL into the fork tube, slowly pump the damper rod 10 or more times, position the damper rod in the fully bottomed position and pour the remaining amount of TYPE E FORK OIL into the fork tube. THEN using a PRO-LEVEL OIL GAUGE (Part No. HD-59000A) or similar adjust the oil level to 5.04 in. (128 mm). THEN carefully clean and install the spring, the spring collar, and the spacers with the sharp edge created when they were stamped out when manufactured, facing the collar. THEN using a FORK SPRING COMPRESSION TOOL such as (Part No. HD-41549A) push spring collar down and place a SPRING PLATE such as (Part No. HD-41551) between the spacer and the spring collar, install the fork cap and tighten it against the rebound adjuster to 22-29 ft-lbs (29.8-39.3 Nm). THEN tighten the fork cap onto the fork tube to 11-22 ft-lbs (14.9-29.8 Nm), install the spring adjuster plate, replace the O-rings on the spring preload adjuster and lubricate them with fork oil. THEN install the spring preload adjuster and the stopper ring and carefully drive the slider cover into the slider.


INSTALLATION

Insert both fork side assemblies up through the fork stem and bracket and upper bracket and tighten the fork stem bracket pinch bolt(s) to 30-35 ft-lbs (40.7-47.5 Nm). Then re-install the headlamp bracket, install the front fender, install the front wheel and the brake caliper When the motorcycle is again ready for the road adjust the headlamp and road test the motorcycle.

Oct 01, 2010 | 2001 Harley Davidson FXD Dyna Super Glide

2 Answers

How do you cahange front fork oil in a 2001 fxdx


raise front wheel .find socket head drain plugs @ bottom of lower legs.remove top nuts to add oil.CAUTION--top nuts are under pressure of fork springs. in the old days we would add a 1'' spacer to springs for a firmer ride.

Sep 23, 2009 | 2001 Harley Davidson FXDX Dyna Super Glide...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

636 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6342 Answers

Mike

Level 3 Expert

4369 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...